![]() |
| ตัวเครื่องภายนอก |
![]() |
| ภายในเครื่อง |
TrendChip TC3162U -> VDSL/ADSL2+ processor
MXIC MX25L1608E -> 16M-BIT [x 1 / x 2] CMOS SERIAL FLASH
![]() |
| TrendChip TC3162U |
![]() |
| MXIC MX25L1608E |
![]() |
| Zentel A3V28S40FTP |
![]() |
| TrendChip TC2206F |
![]() |
| Ralink RT3390L |
![]() |
| Regulator |
1117 -> 800mA Low-Dropout Linear Regulator
![]() |
| พอร์ต Serial |
![]() |
| ใต้บอร์ด |
![]() |
| เสาอากาศ |
Boot Message รหัสผ่านเริ่มต้นคือ 1234
Bootbase Version: VTC_SPI1.8 | 2010/4/8 09:32:52RAM: Size = 16384 KbytesDRAM POST: Testing: 16384KOKFound SPI Flash 2MiB MX25L1606E(05D) at 0xbfc00000RAS Version: 3.40(BYF.11)b1Press any key to enter debug mode within 3 seconds.............................................................Copyright (c) 1994 - 2010 ZyXEL Communications Corp.Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...initialize ch = 0, TC2104ME, TC2206, ethernet address: 50:67:f0:e6:5b:24initialize ch = 1,AP restart , also restart 802.1x and reset EAPoL queuePhyMode = 9ethernet address: 50:67:f0:e6:5b:24tcphy[3]: Link-up at 100F. tx_amp_save=0.tcphy[3]: boosten=1 agccode=9 zfgain=8 ch_idx=41 snr=3Wan Channel init ........ doneInitializing ADSL F/W ........ done==>natTableMemoryInit<==natTableMemoryInit*DOT1X* radius_srv_num = 1*DOT1X* radius_srv_num = 1*DOT1X* radius_srv_num = 1*DOT1X* radius_srv_num = 1*DOT1X* initRadiusSocket[0]: bind socket to 2050 OK*DOT1X* initRadiusSocket[1]: bind socket to 2051 OK*DOT1X* initRadiusSocket[2]: bind socket to 2052 OK*DOT1X* initRadiusSocket[3]: bind socket to 2053 OK*DOT1X* register socket ok - iface-0*DOT1X* register socket ok - iface-1*DOT1X* register socket ok - iface-2*DOT1X* register socket ok - iface-3ANNEXALDNS Hijack switch is 1.Success!NAT session reserved is 512,protocol is 2,port is 80!WSC_MANUFACTURE is ZyXEL nowAP_WSC_DEVICE_NAME is P-660HN-T1A nowAP_WSC_MODEL_NAME is P-660HN-T1A nownow autocwmppara is offTestlab 10set try multimode number to 3 (dropmoErasing 4K Sector...Erasing 4K Sector...writeRomBlock(): Erase OK!de try num 3Erasigng 4K Sector...x64, 1:maxD=128, 2:maxD=511)Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...writeRomBlock(): Erase OK!Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Erasing 4K Sector...Syncookie switch On!Press ENTER to continue...Enter Password : XXXXXCopyright (c) 1994 - 2010 ZyXEL Communications Corp.P-660HN-T1A> ?Valid commands are:sys exit ether wanetherdbg tcephydbg ip bridgedot1q pktqos show setlanP-660HN-T1A>





















































