TP-Link Deco M3W

อุปกรณ์ตัวนี้เป็น Mesh WiFi ครับ

ตัวเครื่อง

ตัวเครื่องไม่มีอะไรมาก คือ มีไฟสถานะ ปุ่ม Reset ไม่มีพอร์ต WAN, LAN อาศัยเชื่อมต่อผ่าน WiFi อย่างเดียว

ใต้เครื่อง

ใต้เครื่องมีตัวเสียบเข้ากับปลั้กไฟตรงๆ

IC ต่างๆ

พอแกะแผ่นกันสัญญาณรบกวนแล้วก็จะพบ IC หลายๆ ตัวครับ

MT7628AN

MEDIATEK MT7628AN -> SoC, MIPS24KEc 580MHz, WiFi 2.4GHz

ESMT M14D1G1664A

ESMT M14D1G1664A -> 8M x 16 Bit x 8 Banks DDR II SDRAM (128 Mbytes)

MT7612EN

MEDIATEK MT7612EN ->  Wi-Fi 5 (a/b/g/n/ac) 866 Mbps PHY rate, PCI-Express 1.1 Interface

SP2

SP2 -> น่าจะเป็น Balun

MSC 589H 816F

MSC 589H 816F -> น่าจะเป็น WiFi Power Amp

Bootlog

Baudrate: 57600

cid reg:00010102, cid:1[04010C0D][04010D08]

DDR Calibration DQS reg = 00008887

DDR Calibration MEMCTRL reg = 0E120003

U-Boot 1.1.3 (Apr 19 2019 - 12:25:44)

Board: Ralink APSoC DRAM:  128 MB

relocate_code Pointer at: 87fb4000

flash manufacture id: c8, device id 40 17

find flash: GD25Q64B

*** Warning - bad CRC, using default environment

============================================

Ralink UBoot Version: 5.0.0.0

--------------------------------------------

ASIC 7628_MP (Port5<->None)

DRAM component: 1024 Mbits DDR, width 16

DRAM bus: 16 bit

Total memory: 128 MBytes

Flash component: SPI Flash

Date:Apr 19 2019  Time:12:25:44

============================================

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####

 estimate memory size =128 Mbytes

RESET MT7628 PHY!!!!!!

Please choose the operation:

   1: Load system code to SDRAM via TFTP.

   2: Load system code then write to Flash via TFTP.

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   7: Load Boot Loader code then write to Flash via Serial.

   9: Load Boot Loader code then write to Flash via TFTP.

   6: auto run sub image.

default: 3

tplink_turn_off_led                                                                                                                                                                                                                        0

3: System Boot system code via Flash.

LEDs ready: . . . _

## Booting image at bc0f0000 ...

   Image Name:   OpenWrt Linux-3.10.14-169495

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    1218246 Bytes =  1.2 MB

   Load Address: 80000000

   Entry Point:  80000000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 128

Starting kernel ...

LINUX started...

 THIS IS ASIC

SDK 5.0.S.0

[    0.000000] Linux version 3.10.14 (jenkins@ubuntusohoredmine) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 Mon Dec 2 17:31:23 CST 2019

[    0.000000]

[    0.000000]  The CPU feqenuce set to 580 MHz

[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)

[    0.000000] Software DMA cache coherency

[    0.000000] Determined physical RAM map:

[    0.000000]  memory: 08000000 @ 00000000 (usable)

[    0.000000] Initrd not found or empty - disabling initrd

[    0.000000] Zone ranges:

[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]

[    0.000000] Movable zone start for each node

[    0.000000] Early memory node ranges

[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]

[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.

[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512

[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 rootfstype=squashfs print-fatal-signals=1

[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)

[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.000000] Writing ErrCtl register=0007a004

[    0.000000] Readback ErrCtl register=0007a004

[    0.000000] Memory: 126128k/131072k available (2694k kernel code, 4944k reserved, 662k data, 224k init, 0k highmem)

[    0.000000] NR_IRQS:128

[    0.000000] console [ttyS1] enabled

[    0.096000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)

[    0.136000] pid_max: default: 32768 minimum: 301

[    0.140000] Mount-cache hash table entries: 512

[    0.144000] NET: Registered protocol family 16

[    0.148000] RALINK_GPIOMODE = 570504c4

[    0.152000] RALINK_GPIOMODE = 570404c4

[    0.252000] ***** Xtal 40MHz *****

[    0.256000] start PCIe register access

[    0.756000] RALINK_RSTCTRL = 2400000

[    0.760000] RALINK_CLKCFG1 = fdbfffc0

[    0.764000]

[    0.764000] *************** MT7628 PCIe RC mode *************

[    1.264000] PCIE0 enabled

[    1.268000] Port 0 N_FTS = 1b105000

[    1.272000] init_rt2880pci done

[    1.292000] bio: create slab <bio-0> at 0

[    1.296000] PCI host bridge to bus 0000:00

[    1.300000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]

[    1.304000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]

[    1.308000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]

[    1.312000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring

[    1.316000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)

[    1.320000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]

[    1.324000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]

[    1.328000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]

[    1.332000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]

[    1.336000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]

[    1.340000] pci 0000:00:00.0: PCI bridge to [bus 01]

[    1.344000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]

[    1.348000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]

[    1.352000] BAR0 at slot 0 = 0

[    1.356000] bus=0x0, slot = 0x0

[    1.360000] res[0]->start = 0

[    1.364000] res[0]->end = 0

[    1.368000] res[1]->start = 20200000

[    1.372000] res[1]->end = 2020ffff

[    1.376000] res[2]->start = 0

[    1.380000] res[2]->end = 0

[    1.384000] res[3]->start = 0

[    1.388000] res[3]->end = 0

[    1.392000] res[4]->start = 0

[    1.396000] res[4]->end = 0

[    1.400000] res[5]->start = 0

[    1.404000] res[5]->end = 0

[    1.408000] bus=0x1, slot = 0x0

[    1.412000] res[0]->start = 20000000

[    1.416000] res[0]->end = 200fffff

[    1.420000] res[1]->start = 0

[    1.424000] res[1]->end = 0

[    1.428000] res[2]->start = 0

[    1.432000] res[2]->end = 0

[    1.436000] res[3]->start = 0

[    1.440000] res[3]->end = 0

[    1.444000] res[4]->start = 0

[    1.448000] res[4]->end = 0

[    1.452000] res[5]->start = 0

[    1.456000] res[5]->end = 0

[    1.460000] Switching to clocksource MIPS

[    1.464000] NET: Registered protocol family 2

[    1.476000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)

[    1.488000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

[    1.500000] TCP: Hash tables configured (established 1024 bind 1024)

[    1.512000] TCP: reno registered

[    1.520000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    1.532000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    1.544000] NET: Registered protocol family 1

[    1.556000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[    1.568000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

[    1.588000] msgmni has been set to 246

[    1.596000] io scheduler noop registered (default)

[    1.612000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[    1.628000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A

[    1.640000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A

[    1.656000] gpiomode2: 5544554

[    1.660000] led=40, on=5, off=5, blinks,=1, reset=1, time=4000

[    1.672000] Ralink gpio driver initialized

[    1.680000] flash manufacture id: c8, device id 40 17

[    1.692000] GD25Q64B(c8 40170000) (8192 Kbytes)

[    1.700000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0

[    1.720000] Creating 5 MTD partitions on "raspi":

[    1.728000] 0x000000000000-0x000000800000 : "ALL"

[    1.740000] 0x000000000000-0x000000020000 : "fs-uboot"

[    1.752000] 0x0000000f0000-0x000000220000 : "os-image"

[    1.764000] 0x000000220000-0x000000790000 : "file-system"

[    1.776000] 0x0000007f0000-0x000000800000 : "radio"

[    1.788000] PPP generic driver version 2.4.2

[    1.796000] PPP MPPE Compression module registered

[    1.804000] NET: Registered protocol family 24

[    1.816000] GMAC1_MAC_ADRH -- : 0x0000000c

[    1.824000] GMAC1_MAC_ADRL -- : 0x432880f7

[    1.832000] Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!

[    1.848000] GMAC1_MAC_ADRH -- : 0x0000000c

[    1.856000] GMAC1_MAC_ADRL -- : 0x4328806c

[    1.868000] PROC INIT OK!

[    1.872000] TCP: cubic registered

[    1.880000] NET: Registered protocol family 10

[    1.888000] NET: Registered protocol family 17

[    1.900000] Bridge firewalling registered

[    1.908000] l2tp_core: L2TP core driver, V2.0

[    1.916000] l2tp_ppp: PPPoL2TP kernel driver, V2.0

[    1.924000] 8021q: 802.1Q VLAN Support v1.8

[    1.932000] registered taskstats version 1

[    1.948000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.

[    1.964000] Freeing unused kernel memory: 224K (80348000 - 80380000)

[    2.728000] init: Console is alive

[    4.748000] init: - preinit -

[    5.684000] FFFFFFCA:FFFFFF87:43:10: 0: 0

[    5.692000] Raeth v3.1 (Tasklet,SkbRecycle)

[    5.704000]

[    5.704000] phy_tx_ring = 0x07fdc000, tx_ring = 0xa7fdc000

[    5.716000]

[    5.716000] phy_rx_ring0 = 0x07fde000, rx_ring[0] = 0xa7fde000

[    5.732000]

[    5.732000] phy_rx_ring0 = 0x07fde000, rx_ring[0] = 0xa7fde000

[    5.760000] GMAC1_MAC_ADRH -- : 0x0000000c

[    5.768000] GMAC1_MAC_ADRL -- : 0x4328806c

[    5.776000] RT305x_ESW: Link Status Changed

[    5.788000] GPIOMODE2: 4000 -

[    5.792000] GPIOMODE2: 4554 +

Press the [f] key and hit [enter] to enter failsafe mode

Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

Before mount_root

mounting /dev/root

kmod: ran 1 iterations

[    9.356000] block: attempting to load /etc/config/fstab

[    9.432000] block: extroot: not configured

After mount_root

[   10.072000] ra2880stop()...Done

[   10.080000] Free TX/RX Ring Memory!

[   10.092000] procd: - early -

[   10.732000] procd: - ubus -

[   11.748000] procd: - init -

Please press Enter to activate this console.

[   11.980000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

[   12.016000] QCA Hy-Fi multicast installation successfully

[   12.036000] Ralink APSoC Hardware Watchdog Timer

[   12.056000] rdm_major = 253

reloadprofile() begin

reloadprofile() end

==reloadConfig()== begin

  ==loadDefaultConfig()== begin

  ==loadConfigToFiles(): default-config to /tmp/defaultconfig== begin

  ==loadConfigToFiles()== end

  ==set_usrconfig_info()== start

  ==set_usrconfig_info()== end

  ==loadDefaultConfig()== end

  ==loadConfigToFiles(): user-config to /tmp/userconfig== begin

  ==loadConfigToFiles()== end

==reloadConfig()===== no need to load emmc-config

  ==loadConfigToFiles(): device-config to /tmp/userconfig== begin

  ==loadConfigToFiles()== end

  ** user-config loaded **

==reloadConfig()== end

merge_extra_config() begin

  ==loadConfigToFiles(): default-config to /tmp/merge== begin

  ==loadConfigToFiles()== end

mergeconfigbycountry() begin

mergeconfigbycountry() country US

mergeconfigbycountry() end

merge_extra_config() end

phylink down boot 1

[   17.724000] FFFFFFCA:FFFFFF87:43:10: 0: 0

[   17.732000] Raeth v3.1 (Tasklet,SkbRecycle)

[   17.740000]

[   17.740000] phy_tx_ring = 0x071f2000, tx_ring = 0xa71f2000

[   17.756000]

[   17.756000] phy_rx_ring0 = 0x07f10000, rx_ring[0] = 0xa7f10000

[   17.768000]

[   17.768000] phy_rx_ring0 = 0x07f10000, rx_ring[0] = 0xa7f10000

[   17.800000] GPIOMODE2: 4000 -

[   17.804000] GPIOMODE2: 4554 +

[   17.812000] GMAC1_MAC_ADRH -- : 0x000098da

[   17.820000] GMAC1_MAC_ADRL -- : 0xc48f3332

[   17.828000] RT305x_ESW: Link Status Changed

[   17.892000] ra2880stop()...Done

[   17.896000] Free TX/RX Ring Memory!

[   17.932000] FFFFFFCA:FFFFFF87:43:10: 0: 0

[   17.940000] Raeth v3.1 (Tasklet,SkbRecycle)

[   17.948000]

[   17.948000] phy_tx_ring = 0x07f16000, tx_ring = 0xa7f16000

[   17.964000]

[   17.964000] phy_rx_ring0 = 0x071f2000, rx_ring[0] = 0xa71f2000

[   17.976000]

[   17.976000] phy_rx_ring0 = 0x071f2000, rx_ring[0] = 0xa71f2000

[   18.008000] GPIOMODE2: 4000 -

[   18.012000] GPIOMODE2: 4554 +

[   18.020000] GMAC1_MAC_ADRH -- : 0x000098da

[   18.028000] GMAC1_MAC_ADRL -- : 0xc48f3332

[   18.036000] RT305x_ESW: Link Status Changed

[   20.988000] IPv6: ADDRCONF(NETDEV_UP): br-wan: link is not ready

[   21.044000] device eth0 entered promiscuous mode

[   21.056000] br-lan: port 1(eth0) entered forwarding state

[   21.064000] br-lan: port 1(eth0) entered forwarding state

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! awn start !!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[   23.068000] br-lan: port 1(eth0) entered forwarding state

[_save_bind_status:624]: echo 1 > /tmp/is_binded

[awnd_get_bind_fap_mac:1574]: Current bind device: AP's mac is (74-DA-88-D4-6D-A0) fapMac:74:DA:88:D4:6D:A0

[awnd_mode_convert:4472]: ========================srcMode:NONE, dstMode:RE======================

apsd: start apsd

whc (repacd): stop repacd-run.sh

whc (repacd): Start:

whc (repacd): GatewayConnectedMode(gwcon_mode): RE

whc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1

whc (repacd): get whc_wifi_config_lock

whc (repacd): starting WHC auto-configuration

whc (repacd): Managed network: lan

whc (repacd): Device type: RE

whc (repacd): Sysmode: Router

whc (repacd): the guest network version of the device is latest, we do nothing(uci_revert_state wifi guest enable)

smartip: start_service smartip

vaplist:

devlist:wifi0,wifi1

whc (repacd): Start:

whc (repacd): GatewayConnectedMode(gwcon_mode): RE

whc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1

[ 1210()] [main 2682] opt:t

[ 1210(lan)] [smartip_create_ibus_thread 69] create ibus thread successfully

[   26.448000] g_back_dev_num:16

[ 1210(lan)] [smartip_check_online 600] open /tmp/is_online error...

GMT-07:00

[ 1210(lan)] [smartip_check_online 600] open /tmp/is_online error...

whc (repacd): wifi config change(is different from /var/state/wifi). wifi_cmd:reload wifi0,wifi1

whc (repacd): Using SON mode for NonCAP

[ 1210(lan)] [smartip_check_online 600] open /tmp/is_online error...

whc (repacd): __repacd_restart_dependencies: Restarting network stack...

wifi reload

nothing to be done for pre_ralinkwifi disable

[ 1210(lan)] [smartip_check_online 600] open /tmp/is_online error...

leds: INFO: Switch.on

insmod wifi modules mt7628(mt7628)

[ 1210(lan)] [smartip_check_online 600] open /tmp/is_online error...

[ 1210(lan)] [smartip_check_online 600] open /tmp/is_online error...

leds: WARN: System time has not been synchronized yet

mac:74-DA-88-D4-6D-A0

mac:98-DA-C4-8F-33-32

2

cap_mac:

2

[   31.952000] ivalue value:

[   31.956000] bind_divece_num:2

[   32.176000] MT7628-->

=== pAd = c0600000, size = 2439240 ===

[   32.188000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x

[   32.204000] <-- RTMPAllocAdapterBlock, Status=0

[   32.212000] MT7628-->RtmpChipOpsHook(492): Not support for HIF_MT yet!

[   32.224000] MT7628-->mt7628_init()-->

[   32.232000] MT7628-->mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))

[   32.244000] MT7628-->e2.bin mt7628_init(1141)::(2), pChipCap->fw_len(64736)

[   32.260000] MT7628-->mt_bcn_buf_init(218): Not support for HIF_MT yet!

[   32.272000] MT7628--><--mt7628_init()

insmod wifi modules mt76x2e(mt76x2e)

leds: INFO: Event: power.on

[   32.352000] led=40, on=4000, off=1, blinks,=4000, reset=1, time=4000

[ 1210(lan)] [smartip_check_online 600] open /tmp/is_online error...

conn-indicator: INFO: -- running --

conn-indicator: [   32.856000] led=42, on=1, off=4000, blinks,=4000, reset=1, time=4000

NOTE: BINDING state: -1 -> 3

conn-indicator: INFO: <30000307> Invoke led: conn[2]

leds: INFO: Event: conn.ap-lost

[   32.932000] led=41, on=5, off=5, blinks,=4000, reset=1, time=4000

leds: INFO: Event: init.done

conn-indicator: NOTE: Mode changed: Unknown -> Router

conn-indicator: NOTE: Role changed: Unknown -> RE

conn-indicator: NOTE: Network type: Unknown -> RE

[   34.512000] MT7612E-->register rt2860

[   34.536000] MT7612E-->

=== pAd = c0e01000, size = 2948544 ===

[   34.548000] <-- RTMPAllocTxRxRingMemory, Status=0

[   34.560000] <-- RTMPAllocAdapterBlock, Status=0

[   34.568000] MT7612E-->pAd->CSRBaseAddress =0xc0d00000, csr_addr=0xc0d00000!

[   34.584000] MT7612E-->device_id =0x7662

[   34.588000] MT7612E-->==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a

[   34.620000] MT7612E-->E2pAccessMode=2

[   34.628000] MT7612E-->cfg_mode=14

[   34.636000] MT7612E-->cfg_mode=14

[   34.644000] MT7612E-->wmode_band_equal(): Band Not Equal!

[   34.940000] MT7612E-->RTMPSetSingleSKUParameters - the country region is 5.

[   34.952000] MT7612E-->RTMPSetSingleSKUParameters - country code is US .

[   34.964000] MT7612E-->RTMPSetSingleSKUParameters - the country DFSType is 1.

[   34.984000] MT7612E-->Loading SKU file: /etc_ro/Wireless/iNIC/SingleSKU_5G_FCC.dat

[   35.108000] MT7612E-->RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5

[   35.120000] MT7612E-->NVM is FLASH mode (pAd->flash_offset = 0x8000)

[   35.184000] MT7628-->TX_BCN DESC a5c2b000 size = 320

[   35.196000] MT7628-->RX[0] DESC a5c2d000 size = 4096

[   35.208000] MT7628-->RX[1] DESC a5c2e000 size = 1024

[   35.296000] MT7628-->AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD

[   35.616000] MT7628-->Smart Carrier Sense = 0

[   35.628000] MT7628-->RTMPSetSingleSKUParameters - the country region is 5.

[   35.640000] MT7628-->RTMPSetSingleSKUParameters - country code is US .

[   35.656000] MT7628-->RTMPSetSingleSKUParameters - the country DFSType is 1.

[   35.668000] MT7628-->Loading SKU file: /etc_ro/Wireless/RT2860/SingleSKU_2G_FCC.dat

[   35.696000] MT7628-->load fw image from fw_header_image

[   35.704000] MT7628-->AndesMTLoadFwMethod1(2288)::pChipCap->fw_len(64736)

[   35.720000] MT7628-->FW Version:1MT7628-->

[   35.728000] MT7628-->FW Build Date:20170411104110MT7628-->

[   35.740000] MT7628-->CmdAddressLenReq:(ret = 0)

[   35.748000] MT7628-->CmdFwStartReq: override = 1, address = 1048576

[   35.760000] MT7628-->CmdStartDLRsp: WiFI FW Download Success

[   35.904000] MT7628-->MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)

[   35.916000] efuse_probe: efuse = 10000002

[   35.924000] MT7628-->RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4

[   35.936000] MT7628-->RtmpEepromGetDefault::e2p_dafault=2

[   35.948000] MT7628-->RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2

[   35.964000] MT7628-->NVM is FLASH mode

[   35.972000] MT7628-->1. Phy Mode = 14

[   36.148000] MT7628-->Country Region from e2p = ffff

[   36.156000] tssi_1_target_pwr_g_band = 33

[   36.164000] MT7628-->2. Phy Mode = 14

[   36.176000] MT7628-->3. Phy Mode = 14

[   36.184000] MT7628-->NICInitPwrPinCfg(11): Not support for HIF_MT yet!

[   36.196000] MT7628-->NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!

[   36.212000] MT7628-->MtAsicInitMac()-->

[   36.280000] MT7628-->mt7628_init_mac_cr()-->

[   36.288000] MT7628-->MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!

[   36.304000] MT7628-->AntCfgInit(2975): Not support for HIF_MT yet!

[   36.316000] MT7628-->MCS Set = ff ff 00 00 01

[   36.324000] MT7628-->MtAsicSetChBusyStat(861): Not support for HIF_MT yet!

[   36.336000] MT7628-->MtAsicSetRalinkBurstMode(3060): Not support for HIF_MT yet!

[   36.352000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   36.436000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   36.448000] MT7628-->MtAsicSetTxPreamble(3039): Not support for HIF_MT yet!

[   36.464000] MT7628-->CmdSlotTimeSet:(ret = 0)

[   36.476000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   36.492000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   36.508000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0

[   36.520000] MT7628-->ap_ftkd> Initialize FT KDP Module...

[   36.532000] MT7628-->Main bssid = 98:da:c4:8f:33:33

[   36.540000] <==== rt28xx_init, Status=0

[   36.580000] MT7628-->@@@ ed_monitor_exit : ===>

[   36.588000] MT7628-->@@@ ed_monitor_exit : <===

[   36.596000] MT7628-->mt7628_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f, EDCCA_Status=0

[   36.616000] MT7628-->WiFi Startup Cost (ra0): 1.432s

iwconfig ra0

config_vap_mode  device=wifi0 vif=ra0 mode=11ng:[   36.724000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

HT40 channel=0 txpower=

iwpriv ra0 set WirelessMode=9

iwpriv ra0 set HtBw=1

setup_vif_ap vif:ra0

iwpriv ra0 set HideSSID=1

iwpriv ra0 set ApMWDS=1

iwpriv ra0 set AuthMode=WPA2PSK

iwpriv ra0 set EncrypType=AES

iwpriv ra0 set IEEE8021X=0

iwpriv ra0 set WPAPSK=xd27AHCn

iwpriv ra0 set DefaultKeyID=2

iwpriv ra0 set RekeyInterval=0

iwpriv ra0 set ACLClearAll=1

[   37.092000] MT7628-->The Access Control List is empty!

[   37.104000] MT7628-->No need to clear the Access Control List!

iwpriv ra0 set ftenable=0

iwpriv ra0 set MaxStaNum=48

iwpriv ra0 set SSID=zEQQ++VArQP/cMMj

[   37.244000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0

[   37.256000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   37.272000] MT7628-->ap_ftkd> Release FT KDP Module...

[   37.476000] MT7628-->MtAsicSetRalinkBurstMode(3060): Not support for HIF_MT yet!

[   37.492000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   37.572000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   37.588000] MT7628-->MtAsicSetTxPreamble(3039): Not support for HIF_MT yet!

[   37.604000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   37.624000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   37.636000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

[   37.652000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   37.668000] MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0

[   37.684000] MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0

[   37.700000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0

[   37.712000] MT7628-->ap_ftkd> Initialize FT KDP Module...

[   37.724000] MT7628-->Main bssid = 98:da:c4:8f:33:33

=====ifconfig eth0 up ======

[   38.592000] ath_band_steering_netlink_receive 156 pid = 1904

setup_vif_ap vif:ra2

iwpriv ra2 set HideSSID=0

iwpriv ra2 set ApMWDS=0

iwpriv ra2 set AuthMode=WPAPSKWPA2PSK

iwpriv ra2 set EncrypType=TKIPAES

iwpriv ra2 set IEEE8021X=0

iwpriv ra2 set WPAPSK=12345678

iwpriv ra2 set DefaultKeyID=2

iwpriv ra2 set RekeyInterval=0

iwpriv ra2 set ACLClearAll=1

[   38.984000] MT7628-->The Access Control List is empty!

[   38.996000] MT7628-->No need to clear the Access Control List!

iwpriv ra2 set ftenable=0

iwpriv ra2 set MaxStaNum=48

iwpriv ra2 set SSID=TOTWIFI_M4TEST

[   39.100000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0

[   39.112000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   39.128000] MT7628-->ap_ftkd> Release FT KDP Module...

[   39.524000] MT7628-->MtAsicSetRalinkBurstMode(3060): Not support for HIF_MT yet!

[   39.540000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   39.632000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   39.648000] MT7628-->MtAsicSetTxPreamble(3039): Not support for HIF_MT yet!

[   39.664000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   39.684000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   39.700000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   39.716000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

[   39.732000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   39.748000] MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0

[   39.760000] MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0

[   39.776000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0

[   39.792000] MT7628-->ap_ftkd> Initialize FT KDP Module...

[   39.800000] MT7628-->Main bssid = 98:da:c4:8f:33:33

[   39.912000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

[   39.928000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   39.944000] ##### mbss_cr_enable, BssId = 2

[   40.028000] device ra2 entered promiscuous mode

[   40.036000] br-lan: port 2(ra2) entered forwarding state

[   40.048000] br-lan: port 2(ra2) entered forwarding state

Dec  2 16:26:11 /usr/bin/apsd: loop_avoidance_configure_bridge_with_mode:136: Info: configure hyfi bridge with mode RE

Dec  2 16:26:11 /usr/bin/apsd: apsd_check_link_state:204: Error: parse link state /tmp/wifi_runtime_info.5g2

Dec  2 16:26:11 /usr/bin/apsd: apsd_check_link_state:204: Error: parse link state /tmp/wifi_runtime_info.5g2

[   40.704000] MT7628-->RTMPAPSetInformation 4168: target mac = 9a:aa:c4:8f:33:33, Bssid = 98:da:c4:8f:33:33

[   40.724000] MaxHTPhyMode BW:1

[   40.724000] MCS:15

[   40.724000] maxTxPower:27

[   40.724000] Streams:2

[   40.740000] MT7628-->RTMPAPSetInformation 4225: Found phyinfo of mac = 9a:aa:c4:8f:33:33,

 phyCapInfo: maxChWidth = 1, maxMCS = 15, maxTxPower = 27, numStreams = 2, phyMode = 1

[   40.796000] ath_band_steering_netlink_receive 156 pid = 1904

setup_vif_ap vif:ra4

iwpriv ra4 set HideSSID=0

iwpriv ra4 set ApMWDS=0

iwpriv ra4 set AuthMode=OPEN

iwpriv ra4 set EncrypType=NONE

iwpriv ra4 set ACLClearAll=1

[   40.960000] MT7628-->The Access Control List is empty!

[   40.972000] MT7628-->No need to clear the Access Control List!

iwpriv ra4 set ftenable=0

iwpriv ra4 set MaxStaNum=48

iwpriv ra4 set SSID=TOTWIFI_M4TEST_Guest

[   41.056000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0

[   41.072000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   41.084000] MT7628-->ap_ftkd> Release FT KDP Module...

[   41.484000] MT7628-->MtAsicSetRalinkBurstMode(3060): Not support for HIF_MT yet!

[   41.496000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   41.560000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   41.572000] MT7628-->MtAsicSetTxPreamble(3039): Not support for HIF_MT yet!

[   41.592000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   41.608000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   41.628000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   41.640000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

[   41.656000] MT7628-->AddTxSType: already registered TxSType (PID = 34, Format = 0

[   41.672000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   41.688000] MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0

[   41.704000] MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0

[   41.716000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0

[   41.732000] MT7628-->ap_ftkd> Initialize FT KDP Module...

[   41.740000] MT7628-->Main bssid = 98:da:c4:8f:33:33

[   41.808000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

[   41.824000] MT7628-->AddTxSType: already registered TxSType (PID = 34, Format = 0

[   41.840000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   41.856000] ##### mbss_cr_enable, BssId = 4

[   41.936000] device ra4 entered promiscuous mode

[   41.948000] br-lan: port 3(ra4) entered forwarding state

[   41.956000] br-lan: port 3(ra4) entered forwarding state

[   42.096000] MT7612E-->build time =

[   42.104000] 20141115060606a

[   42.108000] MT7612E-->rom patch for E3 IC

[   42.116000] MT7612E-->

[   42.120000] MT7612E-->platform =

[   42.128000] ALPS

[   42.132000] MT7612E-->hw/sw version =

[   42.140000] ▒▒

[   42.144000] MT7612E-->patch version =

[   42.152000]

[   42.164000] MT7612E-->FW Version:0.0.00

[   42.172000] MT7612E-->Build:1

[   42.180000] MT7612E-->Build Time:201511101431____

[   42.188000] MT7612E-->fw for E3 IC

[   42.212000] MT7612E-->RX[0] DESC a59a7000 size = 4096

[   42.224000] MT7612E-->RX[1] DESC a59d0000 size = 4096

[   42.248000] MT7612E-->E2pAccessMode=2

[   42.256000] MT7612E-->cfg_mode=14

[   42.264000] MT7612E-->cfg_mode=14

[   42.272000] MT7612E-->wmode_band_equal(): Band Not Equal!

[   42.568000] MT7612E-->RTMPSetSingleSKUParameters - the country region is 5.

[   42.580000] MT7612E-->RTMPSetSingleSKUParameters - country code is US .

[   42.596000] MT7612E-->RTMPSetSingleSKUParameters - the country DFSType is 1.

[   42.608000] MT7612E-->Loading SKU file: /etc_ro/Wireless/iNIC/SingleSKU_5G_FCC.dat

[   42.700000] MT7612E-->1. Phy Mode = 49

[   42.708000] MT7612E-->get_chl_grp:illegal channel (167)

[   42.716000] MT7612E-->get_chl_grp:illegal channel (167)

[   42.728000] MT7612E-->get_chl_grp:illegal channel (169)

[   42.736000] MT7612E-->get_chl_grp:illegal channel (169)

[   42.748000] MT7612E-->get_chl_grp:illegal channel (171)

[   42.760000] MT7612E-->get_chl_grp:illegal channel (171)

[   42.768000] Mt7612E--> mt76x2_read_chl_pwr:3008 assert (ad->TxPower[choffset].Channel == 42)failed

[   42.788000] MT7612E-->Country Region from e2p = ffff

[   42.796000] MT7612E-->mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1

[   42.812000] MT7612E-->mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0x0, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c

[   42.840000] MT7612E-->2. Phy Mode = 49

[   42.848000] MT7612E-->3. Phy Mode = 49

[   42.856000] MT7612E-->andes_pci_fw_init

[   42.864000] MT7612E-->0x1300 = 00073200

[   42.896000] MT7612E-->AntCfgInit: primary/secondary ant 0/1

[   42.908000] MT7612E-->andes_load_cr:cr_type(2)

[   42.928000] MT7612E-->ChipStructAssign(): MT76x2 hook !

[   42.936000] MT7612E-->MCS Set = ff ff 00 00 01

[   42.944000] MT7612E-->mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42

[   43.052000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   43.068000] MT7612E-->APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)

[   43.092000] MT7612E-->mt76x2_calibration(channel = 42)

[   43.468000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   43.488000] MT7612E-->ap_ftkd> Initialize FT KDP Module...

[   43.496000] MT7612E-->Main bssid = 98:da:c4:8f:33:34

[   43.508000] MT7612E-->original vga value(chain0) = 48

[   43.516000] MT7612E-->original vga value(chain1) = 48

[   43.528000] <==== rt28xx_init, Status=0

[   43.556000] MT7612E-->RTMPDrvOpen(1):Check if PDMA is idle!

[   43.568000] MT7612E-->RTMPDrvOpen(2):Check if PDMA is idle!

[   43.580000] Number of Packet Allocated in open = 530

[   43.588000] Number of Packet Freed in open = 18

iwconfig rai0

config_vap_mode  device=wifi1 vif=rai0 mode=11ac[   43.668000] MT7612E-->:HT80 channel=0 cfg_mode=14

txpower=

iwpriv[   43.680000] MT7612E--> rai0 set Wirelewmode_band_equal(): Band Equal!

ssMode=14

iwpriv rai0 set HtBw=1

iwpriv rai0 set VhtBw=1

setup_vif_ap vif:rai0

iwpriv rai0 set HideSSID=1

iwpriv rai0 set ApMWDS=1

iwpriv rai0 set AuthMode=WPA2PSK

iwpriv rai0 set EncrypType=AES

iwpriv rai0 set IEEE8021X=0

iwpriv rai0 set WPAPSK=xd27AHCn

iwpriv rai0 set DefaultKeyID=2

iwpriv rai0 set RekeyInterval=0

iwpriv rai0 set ACLClearAll=1

iwpriv rai0 set ftenable=0

iwpriv rai0 set MaxStaNum=48

iwpriv rai0 set SSID=zEQQ++VArQP/cMMj

[   44.308000] MT7612E-->@@@ APStop: go to ed_monitor_exit()!!

[   44.320000] MT7612E-->ap_ftkd> Release FT KDP Module...

[   44.524000] MT7612E-->mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42

[   44.592000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   44.608000] MT7612E-->APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)

[   44.636000] MT7612E-->mt76x2_calibration(channel = 42)

[   45.012000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   45.028000] MT7612E-->ap_ftkd> Initialize FT KDP Module...

setup_vif_ap vif:rai2

iwpriv rai2 set HideSSID=0

iwpriv rai2 set ApMWDS=0

iwpriv rai2 set AuthMode=WPAPSKWPA2PSK

iwpriv rai2 set EncrypType=TKIPAES

iwpriv rai2 set IEEE8021X=0

iwpriv rai2 set WPAPSK=12345678

iwpriv rai2 set DefaultKeyID=2

iwpriv rai2 set RekeyInterval=0

iwpriv rai2 set ACLClearAll=1

iwpriv rai2 set ftenable=0

iwpriv rai2 set MaxStaNum=48

iwpriv rai2 set SSID=TOTWIFI_M4TEST

[   46.040000] MT7612E-->@@@ APStop: go to ed_monitor_exit()!!

[   46.056000] MT7612E-->ap_ftkd> Release FT KDP Module...

[   46.452000] MT7612E-->mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42

[   46.520000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   46.536000] MT7612E-->APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)

[   46.568000] MT7612E-->mt76x2_calibration(channel = 42)

[   46.944000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   46.960000] MT7612E-->ap_ftkd> Initialize FT KDP Module...

[   47.008000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   47.136000] device rai2 entered promiscuous mode

[   47.144000] br-lan: port 4(rai2) entered forwarding state

[   47.156000] br-lan: port 4(rai2) entered forwarding state

[   48.016000] MT7612E-->RTMPAPSetInformation 4540: target mac = 9a:da:c4:8f:33:34, Bssid = 98:da:c4:8f:33:34

[   48.036000] MaxHTPhyMode BW:1

[   48.036000] MCS:15

[   48.036000] maxTxPower:17

[   48.036000] Streams:2

[   48.056000] MT7612E-->RTMPAPSetInformation 4595: Found phyinfo of mac = 9a:da:c4:8f:33:34,

 phyCapInfo: maxChWidth = 1, maxMCS = 15, maxTxPower = 17, numStreams = 2, phyMode = 1

[   48.176000] ath_band_steering_netlink_receive 156 pid = 1904

/lib/sync-server/scripts/probe:375:     Warning: I have no IP

setup_vif_ap vif:rai4

iwpriv rai4 set HideSSID=0

iwpriv rai4 set ApMWDS=0

iwpriv rai4 set AuthMode=OPEN

iwpriv rai4 set EncrypType=NONE

iwpriv rai4 set ACLClearAll=1

iwpriv rai4 set ftenable=0

iwpriv rai4 set MaxStaNum=48

iwpriv rai4 set SSID=TOTWIFI_M4T[   48.892000] MT7612E-->EST_Guest

@@@ APStop: go to ed_monitor_exit()!!

[   48.908000] MT7612E-->ap_ftkd> Release FT KDP Module...

[   49.308000] MT7612E-->mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42

[   49.372000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   49.388000] MT7612E-->APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)

[   49.420000] MT7612E-->mt76x2_calibration(channel = 42)

[   49.800000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   49.816000] MT7612E-->ap_ftkd> Initialize FT KDP Module...

[   49.848000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   49.916000] device rai4 entered promiscuous mode

[   49.924000] br-lan: port 5(rai4) entered forwarding state

[   49.936000] br-lan: port 5(rai4) entered forwarding state

Dec  2 16:26:21 /usr/bin/apsd: loop_avoidance_configure_bridge_with_mode:136: Info: configure hyfi bridge with mode RE

nothing to be done for post_ralinkwifi enable

2g:ra0, 5g:rai0

interface5g:rai0

[   50.256000] MT7612E-->RTMPAPSetInformation 4540: target mac = 9a:da:c4:8f:33:34, Bssid = 98:da:c4:8f:33:34

[   50.276000] MaxHTPhyMode BW:1

[   50.276000] MCS:15

[   50.276000] maxTxPower:17

[   50.276000] Streams:2

[   50.296000] MT7612E-->RTMPAPSetInformation 4595: Found phyinfo of mac = 9a:da:c4:8f:33:34,

 phyCapInfo: maxChWidth = 1, maxMCS = 15, maxTxPower = 17, numStreams = 2, phyMode = 1

[   50.356000] device rai0.1 entered promiscuous mode

[   50.384000] device rai0 entered promiscuous mode

[   50.396000] br-lan: port 6(rai0.1) entered forwarding state

[   50.408000] br-lan: port 6(rai0.1) entered forwarding state

interface2g:ra0

[   50.584000] device ra0.1 entered promiscuous mode

[   50.636000] device ra0 entered promiscuous mode

[   50.644000] br-lan: port 7(ra0.1) entered forwarding state

[   50.656000] br-lan: port 7(ra0.1) entered forwarding state

2g:ra0, 5g:rai0

interface5g:rai0

[   51.032000] device rai0.2 entered promiscuous mode

[   51.060000] br-lan: port 8(rai0.2) entered forwarding state

[   51.072000] br-lan: port 8(rai0.2) entered forwarding state

interface2g:ra0

[   51.276000] device ra0.2 entered promiscuous mode

[   51.312000] br-lan: port 9(ra0.2) entered forwarding state

[   51.324000] br-lan: port 9(ra0.2) entered forwarding state

whc (repacd): set wifi done flag

whc (repacd): get whc_wifi_config_lock

whc (repacd): unlock whc_wifi_config_lock

whc (repacd): clear wifi_set_done flag

whc (repacd): starting WHC auto-configuration

whc (repacd): Managed network: lan

whc (repacd): Device type: RE

whc (repacd): Sysmode: Router

whc (repacd): the guest network version of the device is latest, we do nothing(uci_revert_state wifi guest enable)

vaplist:

devlist:

whc (repacd): Using SON mode for NonCAP

whc (repacd): __repacd_restart_dependencies: No changes; not restarting network stack...

2g:ra0, 5g:rai0

interface5g:rai0

interface2g:ra0

2g:ra0, 5g:rai0

interface5g:rai0

interface2g:ra0

whc (repacd): set wifi done flag

whc (repacd): unlock whc_wifi_config_lock

[awnd_wifi_wait_for_done:1373]: *****************wifi has been done*****************

[awnd_loop_re_in[   56.908000] MT7628-->it:4138]:

^^^^Set::OID_AP_VENDOR_IE_SET

^^^^^^^^^^^^^^^^^^^^^^awnd_re_loop^^^^^^^^^^^^^^[   56.928000] MT7612E-->^^^^^^^^^^^^

Set::OID_AP_VENDOR_IE_SET

[ 1210(lan)] [smartip_ibus_handle_wifi_event 2156] AP -> RE

/lib/sync-server/scripts/probe:375:     Warning: I have no IP

[   58.648000] MT7628-->RTMPAPSetInformation 4168: target mac = 9a:aa:c4:8f:33:33, Bssid = 98:da:c4:8f:33:33

[   58.668000] MaxHTPhyMode BW:1

[   58.668000] MCS:15

[   58.668000] maxTxPower:27

[   58.668000] Streams:2

[   58.688000] MT7628-->RTMPAPSetInformation 4225: Found phyinfo of mac = 9a:aa:c4:8f:33:33,

 phyCapInfo: maxChWidth = 1, maxMCS = 15, maxTxPower = 27, numStreams = 2, phyMode = 1

[   58.788000] MT7612E-->RTMPAPSetInformation 4540: target mac = 9a:da:c4:8f:33:34, Bssid = 98:da:c4:8f:33:34

[   58.808000] MaxHTPhyMode BW:1

[   58.808000] MCS:15

[   58.808000] maxTxPower:17

[   58.808000] Streams:2

[   58.828000] MT7612E-->RTMPAPSetInformation 4595: Found phyinfo of mac = 9a:da:c4:8f:33:34,

 phyCapInfo: maxChWidth = 1, maxMCS = 15, maxTxPower = 17, numStreams = 2, phyMode = 1

[   58.868000] ath_band_steering_netlink_receive 156 pid = 2942

[   58.900000] ath_band_steering_netlink_receive 156 pid = 2942

[   58.980000] ath_band_steering_netlink_receive 156 pid = 2942

[_wifi_exec_cmd:228]: wifi cmd(touch /tmp/wifi_scan_running)

[   60.132000] MT7628-->ApSiteSurvey: BssTableInit!!!

[_wifi_exec_cmd:228]: wifi cmd(iwpriv rai0 set PartialScan=1)

mt7628_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0000] MT7628--> PartialScan=1)

[   60.196000] MT7612E-->ApSiteSurvey: BssTableInit!!!

[   60.252000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#36(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   60.416000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   60.460000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   60.524000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

========= MODE: cloud_awn_update begin ==========

mode: RE

[   60.772000] MT7628-->mt7628_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0

[   60.848000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#40(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   61.012000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   61.056000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   61.120000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   61.372000] MT7628-->mt7628_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0

[   61.448000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#44(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   61.616000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   61.660000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   61.724000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   61.972000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0

[   62.048000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#48(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   62.216000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   62.260000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   62.324000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   62.572000] MT7628-->mt7628_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0

[   62.648000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#149(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   62.816000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   62.860000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   62.924000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   63.172000] MT7628-->mt7628_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0

[   63.248000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#153(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   63.412000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   63.456000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   63.520000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   63.772000] MT7628-->mt7628_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0

[   63.848000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#157(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   64.012000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   64.056000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   64.120000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   64.372000] MT7628-->mt7628_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0

[   64.448000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#161(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   64.616000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   64.660000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   64.724000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   64.972000] MT7628-->mt7628_switch_channel(): Switch to Ch#9(2T2R), BBP_BW=0

[   65.048000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#165(2T2R), BBP_BW=0, bbp_ch_idx=0)

[   65.216000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   65.260000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   65.324000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   65.572000] MT7628-->mt7628_switch_channel(): Switch to Ch#10(2T2R), BBP_BW=0

[   65.648000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=0)

[   65.816000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   65.860000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   66.172000] MT7628-->mt7628_switch_channel(): Switch to Ch#11(2T2R), BBP_BW=0

[   66.416000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   66.460000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   66.772000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[   66.816000] MT7628-->mt7628_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=1

[_wifi_exec_cmd:228]: wifi cmd(rm /tmp/wifi_scan_running)

[awnd_get_scan_result:1312]: ra0    idx:0, ssid:                                , bssid:7E:DA:88:D4:6D:A2, rssi:35  , channel:9  , uplinkMask:0    , uplinkrate:0    , pathRate:270

[awnd_get_scan_result:1322]: awnd_net_type:0  ,awnd_level:0 , awnd_weight:0, wait:0, lanip:c0a84401, dns:c0a80000             server_detected:0, server_touch_time:0, awnd_mac:74:DA:88:D4:6D:A0

[awnd_get_scan_result:1312]: rai0   idx:0, ssid:                                , bssid:7E:DA:88:D4:6D:A3, rssi:22  , channel:40 , uplinkMask:0    , uplinkrate:0    , pathRate:351

[awnd_get_scan_result:1322]: awnd_net_type:0  ,awnd_level:0 , awnd_weight:0, wait:0, lanip:c0a84401, dns:c0a80000             server_detected:0, server_touch_time:0, awnd_mac:74:DA:88:D4:6D:A0

[awnd_scan_handle_rootap:2821]: Find a better ap subnet

[_wifi_exec_cmd:228]: wifi cmd(iwpriv apcli0 set ApCliEnable=0 &)

[_wifi_exec_cmd:228]: wifi cmd(iwpriv apclii0 set ApCliEnable=0 &)

[_wifi_exec_cmd:228]: wifi cmd(iwpriv apcli0 set ApCliEnable=1)

[_wifi_exec_cmd:228]: wifi cmd(iwpriv apclii0 set ApCliEnable=1)

whc (repacd): stop repacd-run.sh

whc (repacd): Start:

whc (repacd): GatewayConnectedMode(gwcon_mode): RE

whc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1

whc (repacd): get whc_wifi_config_lock

whc (repacd): starting WHC auto-configuration

whc (repacd): Managed network: lan

whc (repacd): Device type: RE

whc (repacd): Sysmode: Router

whc (repacd): the guest network version of the device is latest, we do nothing(uci_revert_state wifi guest enable)

new_value:1, old_value:0

change:64, action:16

new_value:7E:DA:88:D4:6D:A2, old_value:

change:64, action:16

new_value:1, old_value:0

change:192, action:16

new_value:7E:DA:88:D4:6D:A3, old_value:

change:192, action:16

new_value:9, old_value:0

change:4288, action:24

new_value:40, old_value:0

change:12480, action:24

/lib/sync-server/scripts/probe:375:     Warning: I have no IP

vaplist:apcli0,apclii0

devlist:wifi0,wifi1

[awnd_mode_convert:4472]: ========================srcMode:RE, dstMode:RE======================

whc (repacd): wifi config change(is different from /var/state/wifi). wifi_cmd:mode,vap wifi0,wifi1 apcli0,apclii0

whc (repacd): Using SON mode for NonCAP

whc (repacd): __repacd_restart_dependencies: Restarting network stack...

whc update:mode,vap

wifi_update action(mode vap) device(wifi0 wifi1) vap(apcli0 apcl[   70.796000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

ii0)

wifi_mode:[   70.812000] MT7628-->AddTxSType: already registered TxSType (PID = 34, Format = 0

wifi0 wifi1

con[   70.828000] MT7628-->AddTxSType: already registered TxSType (PID = 36, Format = 0

fig_vap_mode  device=wifi0 vif=ra0 mode=11ng:HT40 channel=9 txpower=

iwpriv ra0 set WirelessMode=9

iwpriv ra0 set HtBw=1

iwpriv ra0 set Channel=9

[   70.884000] MT7628-->mt7628_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=1

[   70.900000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0

[   70.916000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   70.928000] MT7628-->ap_ftkd> Release FT KDP Module...

[   71.328000] MT7628-->MtAsicSetRalinkBurstMode(3060): Not support for HIF_MT yet!

[   71.340000] MT7628-->MtAsicSetPiggyBack(796): Not support for HIF_MT yet!

[   71.400000] MT7628-->mt7628_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=1

[   71.412000] MT7628-->MtAsicSetTxPreamble(3039): Not support for HIF_MT yet!

[   71.432000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   71.448000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   71.468000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   71.484000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

[   71.496000] MT7628-->AddTxSType: already registered TxSType (PID = 34, Format = 0

[   71.512000] MT7628-->AddTxSType: already registered TxSType (PID = 36, Format = 0

[   71.528000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   71.544000] MT7628-->AddTxSType: already registered TxSType (PID = 6, Format = 0

[   71.560000] MT7628-->AddTxSType: already registered TxSType (PID = 8, Format = 0

[   71.572000] MT7628-->MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0

[   71.588000] MT7628-->ap_ftkd> Initialize FT KDP Module...

[   71.600000] MT7628-->Main bssid = 98:da:c4:8f:33:33

[   71.608000] MT7628-->Set_Channel_Proc 515: send_event_to_network_roaming

config_vap_mode  device=wifi1 vif=rai0 mode=11ac:HT80 channel=40 txpower=

iwpri[   71.648000] MT7612E-->v rai0 set Wirelcfg_mode=14

essMode=14

[   71.660000] MT7612E-->wmode_band_equal(): Band Equal!

iwpriv rai0 set HtBw=1

iwpriv rai0 set VhtBw=1

iwpriv rai0 set Channel=40

[   71.688000] MT7612E-->@@@ APStop: go to ed_monitor_exit()!!

[   71.704000] MT7612E-->ap_ftkd> Release FT KDP Module...

[   72.100000] MT7612E-->mt76x2_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=40, HT-CentCh=38, VHT-CentCh=42

[   72.168000] MT7612E-->mt76x2_switch_channel(): Switch to Ch#42(2T2R), BBP_BW=2, bbp_ch_idx=1)

[   72.184000] MT7612E-->APStartUp(): AP Set CentralFreq at 42(Prim=40, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)

[   72.216000] MT7612E-->mt76x2_calibration(channel = 42)

[   72.592000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   72.608000] MT7612E-->ap_ftkd> Initialize FT KDP Module...

[   72.620000] BW and Channel is ready

[   72.628000] MT7612E-->Set_Channel_Proc 499: send_event_to_network_roaming

wifi_vap:apcli0 apclii0

wifi_vap to config_vap(apcli0)

config_vap  vif(apcli0) action() phy(wifi0) mode(sta) disabled(0)

config_vap vif:apcli0 disabled:0

down_vap apcli0

cat: read error: Invalid argument

Command failed: Not found

wifi_vap to config_vap(apclii0)

config_vap  vif(apclii0) action() phy(wifi1) mode(sta) disabled(0)

config_vap vif:apclii0 disabled:0

down_vap apclii0

[create_process]vif:apcli0 mode:sta brname: start_hostapd: start_wapid:

cat: read error: Invalid argument

setup_vif_sta ifname(apcli0) ssid(zEQQ++VArQP/cMMj) bssid(7E:DA:88:D4:6D:A2) encrytion(psk2+ccmp) password(xd27AHCn)

iwpriv apcli0 set ApCliEnable=0

iwpriv apcli0 set MACRepeaterEn=0

iwpriv apcli0 set ApCliMWDS=1

iwpriv apcli0 set ApCliAuthMode=WPA2PSK

iwpriv apcli0 set ApCliEncrypType=AES

iwpriv apcli0 set IEEE8021X=0

iwpriv apcli0 set ApCliWPAPSK=xd27AHCn

iwpriv apcli0 set ApCliSsid=zEQQ++VArQP/cMMj

iwpriv apcli0 set ApCliBssid=7E:DA:88:D4:6D:A2

iwpriv apcli0 set ApCliEnable=1

Command failed: Not found

up_all_vap DEVICES(wifi0 wifi1)

[create_process]vif:apclii0 mode:sta brname: start_hostapd: start_wapid:

setup_vif_sta ifname(apclii0) ssid(zEQQ++VArQP/cMMj) bssid(7E:DA:88:D4:6D:A3) encrytion(psk2+ccmp) password(xd27AHCn)

iwpriv apclii0 set ApCliEnable=0

iwpriv apclii0 set MACRepeaterEn=0

iwpriv apclii0 set ApCliMWDS=1

iwpriv apclii0 set ApCliAuthMode=WPA2PSK

iwpriv apclii0 set ApCliEncrypType=AES

iwpriv apclii0 set IEEE8021X=0

iwpriv apclii0 set ApCliWPAPSK=xd27AHCn

iwpriv apclii0 set ApCliSsid=zEQQ++VArQP/cMMj

iwpriv apclii0 set ApCliBssid=7E:DA:88:D4:6D:A3

iwpriv apclii0 set ApCliEnable=1

[   74.652000] MT7628-->RTMPAPSetInformation 4168: target mac = 9a:aa:c4:8f:33:33, Bssid = 98:da:c4:8f:33:33

[   74.672000] MaxHTPhyMode BW:1

[   74.672000] MCS:15

[   74.672000] maxTxPower:27

[   74.672000] Streams:2

[   74.692000] MT7628-->RTMPAPSetInformation 4225: Found phyinfo of mac = 9a:aa:c4:8f:33:33,

 phyCapInfo: maxChWidth = 1, maxMCS = 15, maxTxPower = 27, numStreams = 2, phyMode = 1

[   74.744000] MT7612E-->RTMPAPSetInformation 4540: target mac = 9a:da:c4:8f:33:34, Bssid = 98:da:c4:8f:33:34

[   74.764000] MaxHTPhyMode BW:1

[   74.764000] MCS:15

[   74.764000] maxTxPower:17

[   74.764000] Streams:2

[   74.784000] MT7612E-->RTMPAPSetInformation 4595: Found phyinfo of mac = 9a:da:c4:8f:33:34,

 phyCapInfo: maxChWidth = 1, maxMCS = 15, maxTxPower = 17, numStreams = 2, phyMode = 1

[   74.836000] ath_band_steering_netlink_receive 156 pid = 2942

[   75.464000] MT7628-->AddTxSType: already registered TxSType (PID = 32, Format = 0

[   75.480000] MT7628-->AddTxSType: already registered TxSType (PID = 34, Format = 0

[   75.496000] MT7628-->AddTxSType: already registered TxSType (PID = 36, Format = 0

[   75.512000] MT7628-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

[   76.572000] MT7612E-->The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8

2g:ra0 apcli0, 5g:rai0 apclii0

interface5g:rai0

interface5g:apclii0

[   76.948000] device apclii0.1 entered promiscuous mode

[   76.992000] device apclii0 entered promiscuous mode

[   77.004000] br-lan: port 10(apclii0.1) entered forwarding state

[   77.016000] br-lan: port 10(apclii0.1) entered forwarding state

interface2g:ra0

interface2g:apcli0

[   77.264000] device apcli0.1 entered promiscuous mode

[   77.300000] device apcli0 entered promiscuous mode

[   77.312000] br-lan: port 11(apcli0.1) entered forwarding state

[   77.324000] br-lan: port 11(apcli0.1) entered forwarding state

[   77.548000] MT7628-->MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!

[   77.564000] MT7628-->PeerPairMsg3Action(1)-1: update CCMP_BC_PN to 1243410

[   77.576000] MT7628-->MWDSAPCliPeerEnable enabled MWDS for entry : 7e-da-88-d4-6d-a2

[   77.592000] MT7628-->SET_MWDS_OPMODE_APCLI OK!

2g:ra0 apcli0, 5g:rai0 apclii0

interface5g:rai0

interface5g:apclii0

[   77.776000] device apclii0.2 entered promiscuous mode

[   77.808000] br-lan: port 12(apclii0.2) entered forwarding state

[   77.820000] br-lan: port 12(apclii0.2) entered forwarding state

interface2g:ra0

interface2g:apcli0

[   78.068000] device apcli0.2 entered promiscuous mode

[   78.116000] br-lan: port 13(apcli0.2) entered forwarding state

[   78.128000] br-lan: port 13(apcli0.2) entered forwarding state

[   78.148000] ============>ApCliCheckVht

[   78.172000] MT7612E-->PeerPairMsg3Action(1): update CCMP_BC_PN to 0

[   78.184000] MT7612E-->SET_MWDS_OPMODE_APCLI OK!

[   78.516000] br-lan: received packet on apcli0.2 with own address as source address

[   78.532000] br-lan: received packet on apcli0.2 with own address as source address

[   78.996000] br-lan: received packet on apcli0.1 with own address as source address

[   79.012000] br-lan: received packet on apcli0.1 with own address as source address

whc (repacd): set wifi done flag

whc (repacd): unlock whc_wifi_config_lock

/lib/sync-server/scripts/probe:375:     Warning: I have no IP

[   79.764000] br-lan: received packet on apcli0.2 with own address as source address

[   79.780000] br-lan: received packet on apcli0.2 with own address as source address

[awnd_wifi_wait_for_done:1373]: *****************wifi has been d[   80.676000] MT7628-->one*************Set::OID_AP_VENDOR_IE_SET

****

[awnd_[   80.692000] MT7612E-->loop_re_init:413Set::OID_AP_VENDOR_IE_SET

8]:

^^^^^^^^^^^^^^^^^^^^^^^^^^awnd_re_loop^^^^^^^^^^^^^^^^^^^^^^^^^^

[awnd_write_rt_info:1752]: bindStatus:4

leds: INFO: Even[   81.148000] led=43, on=4000, off=1, blinks,=4000, reset=1, time=4000

t: wifi2g.on

[awnd_write_rt_i[   81.172000] MT7628-->nfo:1761]: link_Set::OID_AP_VENDOR_IE_SET

state:1, buf:ubu[   81.188000] MT7612E-->s send link_statSet::OID_AP_VENDOR_IE_SET

e '{ LINK_WIFI_2G: 1, LINK_WIFI_5G: 0, LINK_WIFI_5G_2: 0, LINK_PLC: 0, LINK_ETH0: 0, LINK_ETH1: 0 }'

[awnd_write_rt_info:1752]: bindStatus:4

leds: INFO: Even[   81.244000] led=39, on=4000, off=1, blinks,=4000, reset=1, time=4000

t: wifi5g.on

[awnd_write_rt_i[   81.268000] MT7628-->nfo:1761]: link_Set::OID_AP_VENDOR_IE_SET

state:3, buf:ubu[   81.284000] MT7612E-->s send link_statSet::OID_AP_VENDOR_IE_SET

e '{ LINK_WIFI_2[   81.300000] MT7628-->G: 1, LINK_WIFI_Set::OID_AP_VENDOR_IE_SET

5G: 1, LINK_WIFI_5G_2: 0, LINK_PLC: 0, LINK_ETH0[   81.320000] MT7612E-->: 0, LINK_ETH1: Set::OID_AP_VENDOR_IE_SET

0 }'

conn-indicator: NOTE: AP MAC changed: (null) -> 74:da:88:d4:6d:a0

conn-indicator: NOTE: Network type: RE -> FAP

[ 1210(lan)] [smartip_get_cap_mac 721] cap_mac:  -> 74:DA:88:D4:6D:A0

mac:74-DA-88-D4-6D-A0

mac:98-DA-C4-8F-33-32

2

cap_mac:74-DA-88-D4-6D-A0

2

[   81.484000] ivalue value:

[   81.488000] bind_divece_num:2

[ 1210(lan)] [smartip_get_cap_mac 742] cap_mac was changed: 74:DA:88:D4:6D:A0

[   81.556000] MT7628-->Rcv Wcid(1) AddBAReq

[   81.564000] MT7628-->Start Seq = 00000000

[   82.056000] MT7612E-->PeerAddBAReqActionForRecv(1538) Rcv Wcid(1) AddBAReq

[   82.068000] MT7612E-->BARecSessionAdd(717) Start Seq = 00000000

[   85.300000] br-lan: received packet on apclii0.1 with own address as source address

[   85.316000] br-lan: received packet on apclii0.1 with own address as source address

[   88.684000] br-lan: received packet on apclii0.2 with own address as source address

[   88.700000] br-lan: received packet on apclii0.2 with own address as source address

conn-indicator: INFO: <31310307> Invoke led: con[   90.660000] led=42, on=1, off=4000, blinks,=4000, reset=1, time=4000

n[1]

leds: INFO[   90.676000] led=41, on=4000, off=1, blinks,=4000, reset=1, time=4000

: Event: conn.offline

conn-indicator: NOTE: Connectivity changed: FAP.LOST(0x7) -> OFFLINE(0x1)

conn-indicator: INFO: Request inet

conn-indicator: ERR: 1th attr(data) not found

conn-indicator: ERR: Invalid response

conn-indicator: INFO: Request inet

conn-indicator: ERR: 1th attr(data) not found

conn-indicator: ERR: Invalid response

conn-indicator: INFO: Request inet

========= MODE: AP is in sync list of RE =========

========= MODE: update awn feature info to cloud ==========

conn-indicator: INFO: Request inet

conn-indicator: INFO: Request inet

conn-indicator: INFO: <31310301> Invoke led: conn[0]

leds: INFO: Even[  102.916000] led=42, on=4000, off=1, blinks,=4000, reset=1, time=4000

t: conn.online

conn-indicator: NOTE: Connectivity changed: OFFLINE(0x1) -> ONLINE(0x0)

[  102.988000] led=41, on=1, off=4000, blinks,=4000, reset=1, time=4000

/usr/lib/lua/luci/controller/admin/sync.lua:281:        sync_get_info begin()

sync_get_compatible_info

/usr/lib/lua/luci/controller/admin/sync.lua:350:        sync_get_info end()

req:    {"method":"getDeviceUserInfo","params":{"deviceId":"80196C145DB50698C311321114EF56A41BAFAD98"}}

re:     0

{"id":3,"error_code":0,"result":{"margin":8,"userList":[{"role":0,"cloudUserName":"kumtornsamui@gmail.com","nickname":"kumtornsamui","bindingTime":1586239176633}]}}

req:    {"method":"saveDeviceFeatureInfo","params":{"featureInfo":{"version":1}}}

re:     0

{"id":4,"error_code":0}

========== CLOUD: RE clear feature info success =========

/usr/lib/lua/luci/controller/admin/sync.lua:355:        sync_get_cfg begin()

/usr/lib/lua/luci/controller/admin/sync.lua:438:        sync_get_cfg end()

M3W login: root

Password: [ 1210(lan)] [smartip_re_get_ap_ip 521] Current mesh device: AP's ip is (192.168.68.1)

Login incorrect

M3W login: notify_check_client: current time is 1588492463

client triggers is opened.

Login timed ouPlease press Enter to activate this console.

M3W login: root

Password:

Login incorrect

M3W login: root

Password:

Login incorrect

M3W login:

Login timed ouPlease press Enter to activate this console.

M3W login: root

Password:

Login incorrect

M3W login: root

Password:

Login incorrect

M3W login:

Login timed ouPlease press Enter to activate this console.

[18681.924000] MT7612E-->ap_cmm_peer_assoc_req_action(1109) - MBSS(4), receive ASSOC request from 50:29:f5:97:ad:4d. Send response (Status=0)

[18682.048000] da match,0x9adcc48f3334

[18682.056000] MT7612E-->RTMP_TimerListRelease: release timer obj c104714c!

[18682.068000] MT7612E-->MacTableDeleteEntry 1079: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED

[18682.088000] MT7612E-->RTMP_TimerListRelease: release timer obj c1046f64!

[18682.104000] MT7612E-->RTMP_TimerListRelease: release timer obj c1046f94!

[18682.116000] MT7612E-->RTMP_TimerListRelease: release timer obj c10473a4!

[18687.452000] MT7628-->ap_cmm_peer_assoc_req_action(1374) - MBSS(4), receive ASSOC request from 50:29:f5:97:ad:4d. Send response (Status=0)

[18687.476000] MT7628-->MWDSAPPeerEnable: ifIndex: 4

[18687.524000] MT7628-->RRM_EnqueueNeighborRep() : send Neighbor RSP

[18697.408000] MT7628-->Rcv Wcid(2) AddBAReq

[18697.416000] MT7628-->Start Seq = 00000020

[18700.948000] MT7628-->2b, flush one!

[18707.484000] MT7628-->34, flush one!

[18707.912000] MT7628-->35, flush one!

[18708.080000] MT7628-->36, flush one!

[19009.636000] MT7628-->ageout 50:29:f5:97:ad:4d after 300-sec silence

[19009.648000] MT7628-->Send DEAUTH - Reason = 3 frame  TO 50 29 f5 97 ad 4d

[19009.660000] MT7628-->MacTableDeleteEntry 1111: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED

[19009.680000] 7628: wireless sendEx event: 8c04

[19579.888000] MT7628-->ap_cmm_peer_assoc_req_action(1374) - MBSS(4), receive ASSOC request from 70:b7:aa:07:2c:33. Send response (Status=0)

[19579.916000] MT7628-->MWDSAPPeerEnable: ifIndex: 4

[19591.948000] da match,0x9acac48f3333

[19591.956000] MT7628-->MacTableDeleteEntry 1111: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED

[19591.976000] 7628: wireless sendEx event: 8c04

[21687.860000] MT7612E-->ap_cmm_peer_assoc_req_action(1109) - MBSS(4), receive ASSOC request from 50:29:f5:97:ad:4d. Send response (Status=0)

[21688.060000] MT7612E-->PeerAddBAReqActionForRecv(1538) Rcv Wcid(2) AddBAReq

[21688.072000] MT7612E-->BARecSessionAdd(717) Start Seq = 00000010

[21691.912000] MT7612E-->de, flush one!

[21692.240000] MT7612E-->e4, flush one!

[21692.564000] MT7612E-->e6, flush one!

[21692.872000] MT7612E-->e8, flush one!

[21703.144000] MT7628-->ap_cmm_peer_assoc_req_action(1374) - MBSS(4), receive ASSOC request from 50:29:f5:97:ad:4d. Send response (Status=0)

[21703.168000] MT7628-->MWDSAPPeerEnable: ifIndex: 4

[21704.232000] MT7628-->RRM_EnqueueNeighborRep() : send Neighbor RSP

[21710.980000] MT7628-->Rcv Wcid(2) AddBAReq

[21710.988000] MT7628-->Start Seq = 00000013

[21712.324000] MT7628-->1f, flush one!

[21715.328000] MT7628-->29, flush one!

[21715.600000] MT7628-->2a, flush one!

[21715.996000] MT7628-->2b, flush one!

[21717.648000] MT7628-->3c, flush one!

[21717.760000] MT7628-->3e, flush one!

[21719.636000] MT7628-->49, flush one!

[21725.056000] MT7628-->53, flush one!

[21993.288000] MT7612E-->RTMP_TimerListRelease: release timer obj c104714c!

[21993.300000] MT7612E-->MacTableDeleteEntry 1079: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED

[21993.320000] MT7612E-->RTMP_TimerListRelease: release timer obj c1046f64!

[21993.332000] MT7612E-->RTMP_TimerListRelease: release timer obj c1046f94!

[21993.348000] MT7612E-->RTMP_TimerListRelease: release timer obj c10473a4!

[22027.688000] MT7628-->ageout 50:29:f5:97:ad:4d after 300-sec silence

[22027.700000] MT7628-->Send DEAUTH - Reason = 3 frame  TO 50 29 f5 97 ad 4d

[22027.712000] MT7628-->MacTableDeleteEntry 1111: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED

[22027.732000] 7628: wireless sendEx event: 8c04

[68574.528000] MT7628-->ap_cmm_peer_assoc_req_action(1374) - MBSS(4), receive ASSOC request from 50:29:f5:97:ad:4d. Send response (Status=0)

[68574.552000] MT7628-->MWDSAPPeerEnable: ifIndex: 4

[68574.568000] MT7628-->RRM_EnqueueNeighborRep() : send Neighbor RSP

[68575.016000] MT7628-->Rcv Wcid(2) AddBAReq

[68575.024000] MT7628-->Start Seq = 00000010

[68575.548000] MT7628-->16, flush one!

[68875.756000] MT7628-->ageout 50:29:f5:97:ad:4d after 300-sec silence

[68875.768000] MT7628-->Send DEAUTH - Reason = 3 frame  TO 50 29 f5 97 ad 4d

[68875.780000] MT7628-->MacTableDeleteEntry 1111: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED

[68875.800000] 7628: wireless sendEx event: 8c04

[69476.664000] MT7628-->ap_cmm_peer_assoc_req_action(1374) - MBSS(4), receive ASSOC request from 50:29:f5:97:ad:4d. Send response (Status=0)

[69476.688000] MT7628-->MWDSAPPeerEnable: ifIndex: 4

[69476.716000] MT7628-->RRM_EnqueueNeighborRep() : send Neighbor RSP

[69477.184000] MT7628-->Rcv Wcid(2) AddBAReq

[69477.192000] MT7628-->Start Seq = 00000010

[69478.260000] MT7628-->2d, flush one!

[69478.724000] MT7628-->2f, flush one!

[69479.020000] MT7628-->36, flush one!

[69479.156000] MT7628-->3c, flush one!

[69479.328000] MT7628-->40, flush one!

[69479.692000] MT7628-->4a, flush one!

[69480.928000] MT7628-->4f, flush one!

[69484.252000] MT7628-->c58, flush one!

[69484.320000] MT7628-->87, flush one!

[69486.020000] MT7628-->9b, flush one!

[69487.200000] MT7628-->a0, flush one!

[69488.308000] MT7628-->APPeerProbeReqAction 896 probe.rssi = 17

[69492.188000] MT7628-->cf, flush one!

[69492.328000] MT7628-->d3, flush one!

[69492.512000] MT7628-->d6, flush one!

[69493.724000] MT7628-->df, flush one!

[69496.308000] MT7628-->e1, flush one!

[69498.236000] MT7628-->e2, flush one!

[69499.568000] MT7628-->102, flush one!

[69501.148000] MT7628-->10e, flush one!

[69501.384000] MT7628-->11e, flush one!

[69501.796000] MT7628-->123, flush one!

[69502.048000] MT7628-->127, flush one!

[69515.752000] MT7628-->ap_cmm_peer_assoc_req_action(1374) - MBSS(4), receive ASSOC request from 50:29:f5:97:ad:4d. Send response (Status=0)

[69515.776000] MT7628-->MWDSAPPeerEnable: ifIndex: 4

[69515.912000] MT7628-->RRM_EnqueueNeighborRep() : send Neighbor RSP

[69823.808000] MT7628-->ageout 50:29:f5:97:ad:4d after 300-sec silence

[69823.820000] MT7628-->Send DEAUTH - Reason = 3 frame  TO 50 29 f5 97 ad 4d

[69823.832000] MT7628-->MacTableDeleteEntry 1111: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED

[69823.852000] 7628: wireless sendEx event: 8c04

/usr/lib/lua/luci/controller/admin/sync.lua:281:        sync_get_info begin()

sync_get_compatible_info

/usr/lib/lua/luci/controller/admin/sync.lua:350:        sync_get_info end()

/usr/lib/lua/luci/controller/admin/sync.lua:355:        sync_get_cfg begin()

/usr/lib/lua/luci/controller/admin/sync.lua:438:        sync_get_cfg end()

[76250.092000] MT7628-->8c, flush one!

/usr/lib/lua/luci/controller/admin/sync.lua:281:        sync_get_info begin()

sync_get_compatible_info

/usr/lib/lua/luci/controller/admin/sync.lua:350:        sync_get_info end()

/usr/lib/lua/luci/controller/admin/sync.lua:355:        sync_get_cfg begin()

/usr/lib/lua/luci/controller/admin/sync.lua:438:        sync_get_cfg end()

ผมไม่ทราบ user/password เข้า shell ครับ

Mikrotik Gigabit Passive Ethernet Repeater( GPeR )

อุปกรณ์ตัวนี้เป็นตัวช่วยเพิ่มระยะสาย LAN จากปกติไม่ควรเกิน 100 เมตร พอต่อเพิ่มไปจะได้ระยะมากขึ้นเป็นกิโลเมตรกว่าๆ หลักการคือรับไฟเลี้ยงผ่านระบบ PoE ทางสาย LAN ภายในจะมี Switch Chip และส่งออกไฟฟ้าพร้อมทั้ง LAN 1Gbps

ซึ่งจริงๆก็เหมือน Switch แบบ 2 พอร์ตที่รับและจ่ายไฟออกได้ครับ

ตัวกล่อง

ตัวกล่องจะประกอบด้วย GPeR และขายึดครับ

หลังกล่อง

หลังกล่องมีข้อมูล MAC Address และ Serial

การต่อใช้งาน

การใช้งานก็ง่ายๆ คือเสียบสายต้นทางเข้าทาง PoE In และเสียบปลายทางเข้า PoE Out ครับ ไม่ต้องตั้งค่าอะไรเลย

ภายใน

เมื่อแกะออกมาจะเจอ PCB ที่มีสติกเกอร์อยู่ พอลอกสติกเกอร์ก็จะเห็นตามรูปล่าง

PCB

ภายในมีส่วนประกอบต่างๆ ดังนี้ครับ

IC

Marvell 88E6341 -> 6 Port Ethernet Switch with 2500Base-X SerDes and Four 10/100/1000Mbps PHYs ตัวนี้คือไอซี Switch 6 พอร์ตแต่ใช้งานจริงแค่ 2 พอร์ต

Microchip 24LC64 -> 64K I2C™ Serial EEPROM ใช้เก็บ Config สำหรับไอซี Switch 

TI TPS54160 -> 1.5-A, 60-V, Step-Down DC/DC Converter with Eco-mode™

PCB ด้านบน

PC13N1ZH -> ตัวนี้เป็น Transformer สำหรับสัญญาณ Ethernet ครับ

HUMAX HR2214A

อุปกรณ์นี้เป็นเราเตอร์ไวไฟของ TRUE Online มี WAN แบบ RJ45

ตัวเครื่อง

ตัวเครื่อง มีเสาอาศ 4 เสา 

หลังเครื่อง

หลังเครื่อง มี 1 WAN RJ45 และ 4 LAN RJ45 มีพอร์ต USB 2.0 ให้ 1 พอร์ต

ภายในเครื่อง

แกะออกมาจะเจอ PCB ด้านล่างเป็นอย่างแรก 

PCB ด้านบน

พลิก PCB อีกด้านจะเจอชิพหลายๆ ตัวดังนี้

RTL8197DN

Realtek RTL8197DN -> SoC with RLX5281 CPU, USB

NT5TU64M16HG-AC

NANYA NT5TU64M16HG-AC -> 1Gb DDR2 RAM

25Q64CSIG

GigaDevice 25Q64CSIG -> 64M-bit SPI NOR Flash

RTL8367RB

Realtek RTL8367RB -> LAYER 2 MANAGED 5+2-PORT 10/100/1000M SWITCH CONTROLLER

RTL8192ER

Realtek RTL8192ER -> 2T2R 802.11bgn 2.4G single-chip that integrates Wireless LAN (WLAN) and a network PCIe controller.

RTL8812AR

Realtek RTL8812AR -> 2T2R 802.11ac solutions with Wireless LAN (WLAN) PCI Express network interface controller.

SKY21 85712

SKYWORKS SKY85712-21 -> 5 GHz WLAN Front-End Module

หน้า Login

ตัวอย่างหน้า Web Login ของเราเตอร์

Bootlog

Booting...

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

@

@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize

@ 0000000h 0c84017h 00000c8h 0000040h 0000017h 0000000h 0000017h 0800000h

@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName

@ 0010000h 0000080h 0001000h 0000800h 0000100h 0000010h 000002dh GD25Q64

@

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

---RealTek(RTL8196D)at 2016.07.08-20:11+0800 v1.2_c1 [16bit](659MHz)

Jump to image start=0x80500000...

decompressing kernel:

Uncompressing Linux... done, booting the kernel.

done decompressing kernel.

start address: 0x80003430

Realtek WLAN driver - version 1.6 (2013-02-21)(SVN:1963)

DFS function - version 1.0.23

Adaptivity function - version 7.1

#######################################################

SKB_BUF_SIZE=3600 MAX_SKB_NUM=768

#######################################################

#######################################################

SKB_BUF_SIZE=3600 MAX_SKB_NUM=768

#######################################################

Probing RTL8186 10/100 NIC-kenel stack size order[3]...

chip name: 8196C, chip revid: 0

NOT YET

eth0 added. vid=9 Member port 0x2...

eth1 added. vid=8 Member port 0x1...

eth2 added. vid=9 Member port 0x4...

eth3 added. vid=9 Member port 0x8...

eth4 added. vid=9 Member port 0x10...

eth5 added. vid=9 Member port 0x0...

[peth0] added, mapping to [eth1]...

Realtek FastPath:v1.03

init started: BusyBox v1.13.4 (2016-08-08 18:18:07 CST)

Init Start...

DEFAULT LANGUAGE_TYPE is [3][0:cn;1:en;2:tw;3:thai;4...]

Init bridge interface...

************* Initialize MAC/PHY parameter *************

[MAC_REG_8812_n]

[PHY_REG_8812_n_hp]

[PHY_REG_PG_8812_new]

[AGC_TAB_8812_n_hp]

[RadioA_8812_n_hp]

[RadioB_8812_n_hp]

[REG_TXPWR_TRK_8812_hp]

************* Initialize MAC/PHY parameter *************

Init Wlan application...

WiFi Simple Config v2.18-wps2.0 (2016.08.08-10:22+0000).

Register to wlan0

Register to wlan1

route: SIOCDELRT: No such process

iwcontrol RegisterPID to (wlan0)

iwcontrol RegisterPID to (wlan1)

IEEE 802.11f (IAPP) using interface br0 (v1.8)

Init WAN Interface...

MiniIGD v1.09.1 (2016.08.08-10:22+0000).

Start NTP daemon

[Debug]Init system in cste...

ROOTFS_OFFSET_T=2b5002 SysCurVerMd5=6680ce24114ed0a4b8bd5a49205e133e

2016-08-08 18:28:19: (log.c.97) server sta

carystudio login:

user = root

password = cs2012

Command - brctl

bridge name bridge id STP enabled interfaces

br0 8000.a0722c4c5328 no eth0

wlan0

wlan1

Command - ifconfig

br0       Link encap:Ethernet  HWaddr A0:72:2C:4C:53:28  

          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:24451 errors:0 dropped:0 overruns:0 frame:0

          TX packets:9980 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:2421974 (2.3 MiB)  TX bytes:3194222 (3.0 MiB)

eth0      Link encap:Ethernet  HWaddr A0:72:2C:4C:53:28  

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:29850 errors:0 dropped:0 overruns:0 frame:0

          TX packets:11930 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:2888475 (2.7 MiB)  TX bytes:3408311 (3.2 MiB)

          Interrupt:12 

eth1      Link encap:Ethernet  HWaddr A0:72:2C:4C:53:29  

          UP BROADCAST RUNNING MULTICAST  MTU:1492  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

          Interrupt:12 

lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:7149 errors:0 dropped:0 overruns:0 frame:0

          TX packets:7149 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:545866 (533.0 KiB)  TX bytes:545866 (533.0 KiB)

wlan0     Link encap:Ethernet  HWaddr A0:72:2C:4C:53:28  

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:3351231 errors:0 dropped:0 overruns:0 frame:0

          TX packets:10591 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:1014635400 (967.6 MiB)  TX bytes:5712861 (5.4 MiB)

          Interrupt:14 

wlan1     Link encap:Ethernet  HWaddr A0:72:2C:4C:53:2C  

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:1692720 errors:0 dropped:0 overruns:0 frame:0

          TX packets:37517 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:382037343 (364.3 MiB)  TX bytes:16756761 (15.9 MiB)

          Interrupt:11 

Command - mount

rootfs on / type rootfs (rw)

/dev/root on / type squashfs (ro,relatime)

proc on /proc type proc (rw,relatime)

ramfs on /var type ramfs (rw,relatime)

/dev/mtdblock3 on /mnt type jffs2 (rw,relatime)

/dev/sda1 on /var/tmp/usb/sda1 type vfat (rw,noatime,nodiratime,fmask=0022,dmask=0000,allow_utime=0022,codepage=cp950,iocharset=utf8)

Command - top

Mem: 55352K used, 56472K free, 0K shrd, 14052K buff, 19020K cached

CPU:   0% usr   0% sys   0% nic 100% idle   0% io   0% irq   0% sirq

Load average: 1.29 0.98 0.97 1/32 30901

[7m  PID  PPID USER     STAT   VSZ %MEM %CPU COMMAND [0m

 1400     1 root     S     2788   2%   0% lighttpd -f /lighttp/lighttpd.conf -m

 1379     1 root     S     2680   2%   0% cste_sub -h 127.0.0.1 -t totolink/rou

 9916     1 root     S     1684   2%   0% minidlna -R -f /etc/minidlna.conf 

 1244     1 root     S     1264   1%   0% dnsmasq 

 1316     1 root     S     1096   1%   0% timelycheck 

 1357     1 root     S     1044   1%   0% cs_broker -c /etc/mosquitto.conf 

26057     1 root     S     1028   1%   0% -sh 

    1     0 root     S     1020   1%   0% init      

30901 26057 root     R     1020   1%   0% top 

 1330     1 root     S      976   1%   0% ntp_inet -x th.pool.ntp.org 

  994     1 root     S      968   1%   0% wscd -start -c /var/wsc-wlan0-wlan1.c

 1249     1 root     S      716   1%   0% lld2d br0 

 1235     1 root     S      676   1%   0% miniigd -e 1 -i br0 

  964     1 root     S      640   1%   0% udhcpd /var/udhcpd.conf 

 1228     1 root     S      620   1%   0% udhcpc -i eth1 -p /etc/udhcpc/udhcpc-

  997     1 root     S      616   1%   0% iwcontrol wlan0 wlan1 

 1255     1 root     S      600   1%   0% reload -k /var/wlsch.conf 

  983     1 root     S      596   1%   0% iapp br0 wlan0 wlan1 

 1312     1 root     S      124   0%   0% fwd 

  717     2 root     SW<      0   0%   0% [mtdblockd]

vlan information 

# ls /proc/net/vlan/

config          hwNatLanVlanId  vlanEnable      wanVlanId

groupIndex      pvid            vlanGroup

# cd /proc/net/vlan/

# ls

config          hwNatLanVlanId  vlanEnable      wanVlanId

groupIndex      pvid            vlanGroup

# cat config

VLAN Dev name    | VLAN ID

Name-Type: VLAN_NAME_TYPE_RAW_PLUS_VID_NO_PAD

# cat hwNatLanVlanId

rtk_hw_nat_lan_vid = 9

# cat vlan

cat: can't open 'vlan': No such file or directory

# cat vlanEnable

vlan enable:0 hw support enable:0

# cat wanVlanId

rtk_wan_vid (NAT) = 8

# cat groupIndex

0

# cat pvid

e0~e8:8,9,9,9,9,9,9,9,9         w0:0,w0-va0~va3:0,0,0,0,w0-vxd:0                w1:0,w1-va0~va3:0,0,0,0,w1-vxd:0

8367r asic pvid:

port 0 pvid 8 pri 0

port 1 pvid 9 pri 0

port 2 pvid 9 pri 0

port 3 pvid 9 pri 0

port 4 pvid 9 pri 0

port 5 pvid 1 pri 0

port 6 pvid 1 pri 0

port 7 pvid 1 pri 0

/proc/cmdline

console=ttyS0,38400 root=/dev/mtdblock1

/proc/cpuinfo

system type : RTL819xD

processor : 0

cpu model : 56322

BogoMIPS : 658.63

hardware watchpoint : no

tlb_entries : 32

mips16 implemented : yes

 /proc/meminfo

MemTotal:         111824 kB

MemFree:           56184 kB

Buffers:           14052 kB

Cached:            18988 kB

SwapCached:            0 kB

Active:            11852 kB

Inactive:          24088 kB

Active(anon):       2900 kB

Inactive(anon):        0 kB

Active(file):       8952 kB

Inactive(file):    24088 kB

SwapTotal:             0 kB

SwapFree:              0 kB

Dirty:                 4 kB

Writeback:             0 kB

AnonPages:          2908 kB

Mapped:             3104 kB

Slab:              18596 kB

SReclaimable:       6084 kB

SUnreclaim:        12512 kB

PageTables:          252 kB

NFS_Unstable:          0 kB

Bounce:                0 kB

WritebackTmp:          0 kB

CommitLimit:       55912 kB

Committed_AS:       5180 kB

VmallocTotal:    1048404 kB

VmallocUsed:         580 kB

VmallocChunk:    1047812 kB

/proc/mtd

dev:    size   erasesize  name

mtd0: 00200000 00001000 "boot+cfg+linux"

mtd1: 005b0000 00001000 "root fs"

mtd2: 00010000 00001000 "dualcfg"

mtd3: 00040000 00001000 "userdata"

 /proc/version

Linux version 2.6.30.9 (wubingdong@localhost.localdomain) (gcc version 4.4.5-1.5.5p4 (GCC) ) #11 Mon Aug 8 18:28:05 CST 2016

ไฟล์ mtdblock และ firmware

download