Sunny MCU and Electronics

วันศุกร์ที่ 23 มีนาคม พ.ศ. 2561

Welltech WellGate 2808 Tear down

อุปกรณ์ตัวนี้เป็น Voice Gateway รองรับ SIP/SIP Trunk ครับ สามารถต่อโทรศัพท์ได้มากสุด 8 พอร์ต

ด้านหน้า

ด้านหน้ามีไฟสถานะต่างๆครับ

ด้านหลัง

ส่วนด้านหลังมีพอร์ต WAN, LAN, RJ11

ใต้เครื่อง

ส่วนของใต้เครื่องก็จะมีสติกเกอร์บอกรายละเอียดของอุปกรณ์ครับ ถัดมาเราก็จะมาดูข้างในกัน

ข้างในเครื่อง

ข้างในเครื่องมี Mainboard อยู่อย่างเดียว ชิปต่างๆ ใน Mainboard ดูตามรูปล่างเลยครับ

ชิปต่างๆ

รายละเอียดของชิปต่างๆ มีดังนี้ครับ

AC494-CB

AudioCodes AC494-CB --> Voice Over Packet SoC มีโมโูลภายในตามรูปด้านล่างครับ

AC494 Function Block

ตัวต่อมาจะเป็น Flash ROM ครับ

MX29GL128FHT2I

MXIC MX29GL128FHT2I --> Parallel Flash 16 MB

FP6116

Feeling Technology FP6116 --> 340KHz, 3A, Asynchronous Step-Down Regulator

74AHCT32D

NXP 74AHCT32D --> Quad 2-input OR gate

AC498-CL

AudioCodes AC498-CL --> 4 Channel DSP for VoIP

PT75115

TI TPS75115QPWP --> FAST-TRANSIENT-RESPONSE 1.5-A LOW-DROPOUT VOLTAGE REGULATORS with Power Good Output

Serial Port

รูปด้านบนน่าจะเป็นพอร์ต Serial ครับ

ใต้ Mainboard

หมดแล้วครับสำหรับด้านบน ต่ามาก็จะเป็นอีกด้านครับ หลักๆก็จะมีชิปแรม กับโมดูล SLIC 4 โมดูลครับ

ใต้ Mainboard

เมื่อถอดโมดูล SLIC ออกก็จะมีหน้าตามภาพครับ

EM63A165TS

EtronTech EM63A165TS --> 16M x 16 bit Synchronous DRAM (SDRAM) เป็น SDRAM 32 MB ครับ มี 2 ชิปดังนั้นความจุรวมคือ 64 MB ครับ

โมดูล SLIC

ตัวต่อมาที่จะมาดูกันคือโมดูล SLIC ครับ ใน 1 โมดูลจะขับสัญญาณโทรศัพท์ได้ 2 ช่องมี 4 โมดูลจึงขับสัญญาณได้ 8 ช่องครับ ในโมดูลเราจะเห็นว่าชิปแบ่งเป็น 2 ชุดอย่างชัดเจนเลย

Si3215-FM

SILICON LABS Si3215-FM --> PROSLIC® PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION

UP1855G

UNISONIC TECHNOLOGIES UP1855G --> HIGH CURRENT TRANSISTOR

โมดูล SLIC

พลิกมาดูอีกด้านของโมดูลก็จะมีชิปอยู่ 1 คู่ครับเป็นเบอร์เดียวกันเลย

BOURNS TISP61089B --> High Voltage Ringing SLIC Protector

โมดูล SLIC ทั้งหมด

โมดูล SLIC ทั้งหมดหน้าตาเหมือนกันเลยครับ

โมดูล SLIC ทั้งหมด

อีกด้านก็เหมือนกันครับ
มาดูในส่วนของ Software กันครับ

ผมต่อเข้าพอร์ต Serial ตามรูปต่อไปครับ

พอร์ต Serial

Boot Message

mips_async=1

cpuclk_in=25000000, cpumulti=13, cpudiv=2

sysclk_in=25000000, sysmulti=10, sysdiv=2

VBUSP CLK CTRL: pllcr(0xa8610a30)=9007, clkcr(0xa8610a20)=1

MIPS CLK CTRL: pllcr(0xa8610a50)=C007, clkcr(0xa8610a40)=1

Basic POST completed... Success.

Last reset cause: Software reset (memory controller also reset)

PSPBoot1.4 rev: 1.4.2.6. Flash Size: 1000000

(c) Copyright 2002-2005 Texas Instruments, Inc. All Rights Reserved.

Press ESC for monitor... 1

(psbl)

Booting...

Launching kernel decompressor.

Kernel decompressor was successful ... launching kernel.

LINUX started...

Config serial console: console=ttyS0,115200n8r

Linux version 2.6.10_dev-malta-mips2_fp_len (root@localhost.localdomain) (gcc version 3.4.6) #154 Thu May 29 16:11:25 CST 2014

CPU revision is: 00018448

TNETV1050 Communication Processor detected

Determined physical RAM map:

memory: 14001000 @ 00000000 (reserved)

memory: 0001f000 @ 14001000 (ROM data)

memory: 0021d000 @ 14020000 (reserved)

memory: 03d43000 @ 1423d000 (usable)

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8r

Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.

Primary data cache 16kB, 4-way, linesize 16 bytes.

Synthesized TLB refill handler (20 instructions).

Synthesized TLB load handler fastpath (32 instructions).

Synthesized TLB store handler fastpath (32 instructions).

Synthesized TLB modify handler fastpath (31 instructions).

PID hash table entries: 256 (order: 8, 4096 bytes)

CPU frequency 162.50 MHz

Using 81.250 MHz high precision timer.

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Freeing Bootloader reserved memory [0x0001f000 @ 0x14001000]

Memory: 62164k/65024k available (1704k kernel code, 2792k reserved, 238k data, 104k init)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Checking for 'wait' instruction... available.

spawn_desched_task(00000000)

desched cpu_callback 3/00000000

ksoftirqd started up.

softirq RT prio: 24.

desched cpu_callback 2/00000000

desched thread 0 started up.

TI Optimizations: Allocating TI-Cached Memory Pool.

Warning: Number of buffers is not configured. Setting default to 512

Using 512 Buffers for TI-Cached Memory Pool.

NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.

NET: Registered protocol family 16

Can't analyze prologue code at 941c8508

JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.

Initializing Cryptographic API

Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled

ttyS0 at (irq = 15) is a 16550A

io scheduler noop registered

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

NET: Registered protocol family 24

elevator: using noop as default io scheduler

Enter avalanche_flash_init.

avalanche flash device: 0x1000000 at 0x10000000.

Primary flash device: Found 1 x16 devices at 0x0 in 16-bit bank

Amd/Fujitsu Extended Query Table at 0x0040

Primary flash device: CFI does not contain boot bank location. Assuming top.

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

Looking for mtd device :mtd0:

Found a mtd0 image (0x120000), with size (0x60000).

Creating 1 MTD partitions on "Primary flash device":

0x00120000-0x00180000 : "mtd0"

Looking for mtd device :mtd1:

Found a mtd1 image (0x20000), with size (0x100000).

Creating 1 MTD partitions on "Primary flash device":

0x00020000-0x00120000 : "mtd1"

Looking for mtd device :mtd2:

Found a mtd2 image (0x200000), with size (0xd00000).

Creating 1 MTD partitions on "Primary flash device":

0x00200000-0x00f00000 : "mtd2"

Looking for mtd device :mtd3:

Found a mtd3 image (0x180000), with size (0x80000).

Creating 1 MTD partitions on "Primary flash device":

0x00180000-0x00200000 : "mtd3"

Looking for mtd device :mtd4:

Found a mtd4 image (0x180000), with size (0x80000).

Creating 1 MTD partitions on "Primary flash device":

0x00180000-0x00200000 : "mtd4"

Looking for mtd device :mtd5:

Found a mtd5 image (0x0), with size (0x20000).

Creating 1 MTD partitions on "Primary flash device":

0x00000000-0x00020000 : "mtd5"

Looking for mtd device :mtd6:

Found a mtd6 image (0xf00000), with size (0x100000).

Creating 1 MTD partitions on "Primary flash device":

0x00f00000-0x01000000 : "mtd6"

NET: Registered protocol family 2

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 4096 bind 8192)

ip_conntrack version 2.1 (508 buckets, 4064 max) - 360 bytes per conntrack

ip_tables: (C) 2000-2002 Netfilter core team

NET: Registered protocol family 1

NET: Registered protocol family 17

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (cramfs filesystem) readonly.

Freeing unused kernel memory: 104k freed

init started: BusyBox v1.2.2 (2009.12.18-02:00+0000) multi-call binary

Starting pid 75, console /dev/console: '/etc/rcS'

mount: Mounting /dev/mtdblock4 on /config_fs2 failed: No such file or directory

This is new image, firmware manager no check fw name.

fwmgr 1.0.0 (R091217) for wg25xx, PPID=75, PID=85, start.

Semaphore_Create STATE_INFO_SEMAPHORE_KEY=0x00000866.

ShareMem_Create STATE_INFO_SHM_KET=0x00000766, cbShm=5344.

chdir CWD=/config_fs.

Prefix=?.

ERROR: opendir /config_fs2, errno=2.

Opened /config_fs.

Hold cur /config_fs/wg28.1.01e.bin.

Hold cur /config_fs/wg28.1.01e.syn.

*** Primary file(s) ***.

/config_fs/wg28.1.01e.bin.

*** Syn file(s) ***.

/config_fs/wg28.1.01e.syn.

chdir CWD=/apps.

Extracting sbin/bdb

Extracting sbin/bdb_d2i

Extracting sbin/bdb_i2d

Extracting sbin/cfgwgos

Extracting sbin/pppoe/etc/ppp/chap-secrets

Extracting sbin/configtitanswitch

Extracting sbin/cpld

Extracting sbin/db_bkup

Extracting sbin/deviceMgr

Extracting sbin/emsclt

Extracting sbin/flasherase

Extracting sbin/iptables

Extracting sbin/kk

Extracting sbin/logmgr

Extracting sbin/mtderase

Extracting sbin/pppoe/etc/ppp/options

Extracting sbin/pppoe/etc/ppp/pap-secrets

Extracting sbin/phoneMgr

Extracting sbin/pk

Extracting sbin/pppoe/usr/sbin/pppd

Extracting sbin/pppoe/usr/sbin/pppoe

Extracting sbin/pppoe/usr/sbin/pppoe-connect

Extracting sbin/pppoe/usr/sbin/pppoe-start

Extracting sbin/rdlog

Extracting sbin/l7-protocols/extra/README

Extracting sbin/restart

Extracting sbin/setmac

Extracting sbin/SipMgr

Extracting sbin/sndsig

Extracting sbin/snmpd

Extracting sbin/sntp

Extracting sbin/tc

Extracting sbin/tr069

Extracting sbin/udhcpc

Extracting sbin/udhcpd

Extracting sbin/updatedd

Extracting sbin/upnpc

Extracting sbin/upnpd

Extracting sbin/utelnetd

Extracting sbin/utelshell

Extracting sbin/l7-protocols/WANTED

Extracting sbin/webs

Extracting sbin/net/updatedd/libdyndns.la

Extracting wwwroot/img/Active.gif

Extracting wwwroot/img/Ball03.gif

Extracting wwwroot/img/Ball04.gif

Extracting wwwroot/img/Ball05_r.gif

Extracting wwwroot/img/checked.gif

Extracting wwwroot/img/Delete.gif

Extracting wwwroot/img/ExpFile.gif

Extracting wwwroot/img/Inactive.gif

Extracting wwwroot/img/Information2.gif

Extracting wwwroot/img/Modify.gif

Extracting wwwroot/img/Progress.gif

Extracting wwwroot/img/sms.gif

Extracting wwwroot/img/tab_d.gif

Extracting wwwroot/img/tab_d_1_g.gif

Extracting wwwroot/img/tab_fond.gif

Extracting wwwroot/img/tab_fond_1_g.gif

Extracting wwwroot/img/tab_g.gif

Extracting wwwroot/img/tab_g_1_g.gif

Extracting wwwroot/img/tab_g_1_l.gif

Extracting wwwroot/img/uncheck.gif

Extracting wwwroot/img/Warning3.gif

Extracting wwwroot/img/head.jpg

Extracting wwwroot/img/left-1.jpg

Extracting wwwroot/img/right.jpg

Extracting wwwroot/img/titbg.jpg

Extracting wwwroot/img/tr.jpg

Extracting sbin/net/linuxigd/dummy.xml

Extracting sbin/net/linuxigd/gateconnSCPD.xml

Extracting sbin/net/linuxigd/gatedesc.xml

Extracting sbin/net/linuxigd/gateicfgSCPD.xml

Extracting sbin/pon.xml

Extracting wwwroot/lib/blank.htm

Extracting wwwroot/lib/Utility.htm

Extracting wwwroot/lib/SubMenu_1.html

Extracting wwwroot/lib/AccessDeny.asp

Extracting wwwroot/advance.asp

Extracting wwwroot/AdvanceSQL.asp

Extracting wwwroot/AppFilter.asp

Extracting wwwroot/AppFilterDeleteSQL.asp

Extracting wwwroot/audio.asp

Extracting wwwroot/AudioSQL.asp

Extracting wwwroot/BackupDB.asp

Extracting wwwroot/Bandwidth.asp

Extracting wwwroot/Bandwidth_Control_del.asp

Extracting wwwroot/Bandwidth_Control_TClistChange.asp

Extracting wwwroot/Bandwidth_Control_TClistConfig.asp

Extracting wwwroot/CallDetailRecord.asp

Extracting wwwroot/CallDetailSQL.asp

Extracting wwwroot/CallerID.asp

Extracting wwwroot/CallerIDSQL.asp

Extracting wwwroot/ClearAllUserDefineKey.asp

Extracting wwwroot/ClearQueueSQL.asp

Extracting wwwroot/CreateDialingRule.asp

Extracting wwwroot/CreateDigitManipulation.asp

Extracting wwwroot/CreatePhoneBook.asp

Extracting wwwroot/CreateSpeedDial.asp

Extracting wwwroot/Debug.asp

Extracting wwwroot/DebugSQL.asp

Extracting wwwroot/DeviceTab.asp

Extracting wwwroot/Device_status.asp

Extracting wwwroot/DHCPServer.asp

Extracting wwwroot/DHCPServer_SQL.asp

Extracting wwwroot/DialedRec.asp

Extracting wwwroot/DialingRule.asp

Extracting wwwroot/DialingRuleDeleteSQL.asp

Extracting wwwroot/DialingRuleSQL.asp

Extracting wwwroot/DialPlanTab.asp

Extracting wwwroot/DigitManipulation.asp

Extracting wwwroot/DigitManipulationSQL.asp

Extracting wwwroot/DMDeleteSQL.asp

Extracting wwwroot/DMZ.asp

Extracting wwwroot/DoImportProcess.asp

Extracting wwwroot/EventNotice.asp

Extracting wwwroot/EventNoticeSQL.asp

Extracting wwwroot/ExecuteCommand.asp

Extracting wwwroot/ExportUserDefineKey.asp

Extracting wwwroot/FeatureKey.asp

Extracting wwwroot/FeatureKeySQL.asp

Extracting wwwroot/FileImport.asp

Extracting wwwroot/File_upload.asp

Extracting wwwroot/File_uploadSQL.asp

Extracting wwwroot/FirmUpgrade.asp

Extracting wwwroot/FlashTime.asp

Extracting wwwroot/FlashTimeSQL.asp

Extracting wwwroot/FXSTab.asp

Extracting wwwroot/General.asp

Extracting wwwroot/GeneralSQL.asp

Extracting wwwroot/GetLineStatus.asp

Extracting wwwroot/GetSIPTrunkStatus.asp

Extracting wwwroot/GSMSettingSQL.asp

Extracting wwwroot/home.asp

Extracting wwwroot/IPFilter.asp

Extracting wwwroot/IPFilterDeleteSQL.asp

Extracting wwwroot/LineSetting.asp

Extracting wwwroot/LineSettingSQL.asp

Extracting wwwroot/LineSetting_Modify.asp

Extracting wwwroot/LineSetting_Modify_normal.asp

Extracting wwwroot/LineSetting_Modify_VFW.asp

Extracting wwwroot/LineSetting_SendGSMSMS.asp

Extracting wwwroot/LineSetting_smsSQL.asp

Extracting wwwroot/LineTab.asp

Extracting wwwroot/Line_status.asp

Extracting wwwroot/Logout.asp

Extracting wwwroot/MACFilter.asp

Extracting wwwroot/MACFilterDeleteSQL.asp

Extracting wwwroot/main.asp

Extracting wwwroot/Maintenance.asp

Extracting wwwroot/MaintenanceSQL.asp

Extracting wwwroot/main_normal.asp

Extracting wwwroot/main_VFW.asp

Extracting wwwroot/menu.asp

Extracting wwwroot/Misscallrec.asp

Extracting wwwroot/ModifyDialingRule.asp

Extracting wwwroot/ModifyDigitManipulation.asp

Extracting wwwroot/ModifyPhoneBook.asp

Extracting wwwroot/ModifySpeedDial.asp

Extracting wwwroot/ModifyUserDefineKey.asp

Extracting wwwroot/NATTab.asp

Extracting wwwroot/NetworkSQL.asp

Extracting wwwroot/Network_status.asp

Extracting wwwroot/PabxMode.asp

Extracting wwwroot/PabxModeSQL.asp

Extracting wwwroot/Password.asp

Extracting wwwroot/PasswordSQL.asp

Extracting wwwroot/PForwardDeleteSQL.asp

Extracting wwwroot/PhoneBook.asp

Extracting wwwroot/PhoneBookDeleteSQL.asp

Extracting wwwroot/PhoneBookExport.asp

Extracting wwwroot/PhoneBookSQL.asp

Extracting wwwroot/Phone_status.asp

Extracting wwwroot/PortFilter.asp

Extracting wwwroot/PortFilterDeleteSQL.asp

Extracting wwwroot/PortForward.asp

Extracting wwwroot/Preference.asp

Extracting wwwroot/PreferenceSQL.asp

Extracting wwwroot/Provisioning - 複製.asp

Extracting wwwroot/Provisioning.asp

Extracting wwwroot/ProvisioningSQL - 複製.asp

Extracting wwwroot/ProvisioningSQL.asp

Extracting wwwroot/RebootPageSQL.asp

Extracting wwwroot/RebootSchedule.asp

Extracting wwwroot/RebootScheduleSQL.asp

Extracting wwwroot/RecvedRec.asp

Extracting wwwroot/RingTone.asp

Extracting wwwroot/RingToneSQL.asp

Extracting wwwroot/RoutePlan.asp

Extracting wwwroot/RoutePlanSQL.asp

Extracting wwwroot/RoutePlan_Modify.asp

Extracting wwwroot/RoutePlan_New.asp

Extracting wwwroot/sip.asp

Extracting wwwroot/sipadv.asp

Extracting wwwroot/sipadvSQL.asp

Extracting wwwroot/SIPAdvTab.asp

Extracting wwwroot/SIPAdvTab_noRingTab.asp

Extracting wwwroot/SIPOthers.asp

Extracting wwwroot/SIPOthersSQL.asp

Extracting wwwroot/SIPProxy.asp

Extracting wwwroot/SIPProxySQL.asp

Extracting wwwroot/SIPSQL.asp

Extracting wwwroot/SIPTab.asp

Extracting wwwroot/SIPTab_noToneTab.asp

Extracting wwwroot/siptime.asp

Extracting wwwroot/SIPTimeSQL.asp

Extracting wwwroot/SIPTrunk.asp

Extracting wwwroot/SIPTrunkExport.asp

Extracting wwwroot/SIPTrunkSQL.asp

Extracting wwwroot/SIPTrunk_Modify.asp

Extracting wwwroot/SIPTrunk_New.asp

Extracting wwwroot/SIPTrunk_status.asp

Extracting wwwroot/sip_account.asp

Extracting wwwroot/SIP_accountSQL.asp

Extracting wwwroot/sip_normal.asp

Extracting wwwroot/sip_VFW.asp

Extracting wwwroot/SNMP.asp

Extracting wwwroot/SNMP_SQL.asp

Extracting wwwroot/SpeedDial.asp

Extracting wwwroot/SpeedDialDeleteSQL.asp

Extracting wwwroot/SpeedDialExport.asp

Extracting wwwroot/SpeedDialSQL.asp

Extracting wwwroot/StatusTab.asp

Extracting wwwroot/time.asp

Extracting wwwroot/TimeSQL.asp

Extracting wwwroot/tone.asp

Extracting wwwroot/ToneSQL.asp

Extracting wwwroot/top.asp

Extracting wwwroot/UploadDefCfg.asp

Extracting wwwroot/UPNP.asp

Extracting wwwroot/UPNPSQL.asp

Extracting wwwroot/URLFilter.asp

Extracting wwwroot/URLFilterDeleteSQL.asp

Extracting wwwroot/UserDefineKey.asp

Extracting wwwroot/UserDefineKeySQL.asp

Extracting wwwroot/UserLogin.asp

Extracting wwwroot/UserLoginSQL.asp

Extracting wwwroot/Voice.asp

Extracting wwwroot/voiceSQL.asp

Extracting wwwroot/Volume.asp

Extracting wwwroot/VolumeSQL.asp

Extracting wwwroot/lib/AdminStyles.css

Extracting wwwroot/lib/MenuStyles.css

Extracting wwwroot/lib/pagestyle.css

Extracting sbin/app2.sh

Extracting sbin/net/checkfile.sh

Extracting sbin/dbrecover.sh

Extracting sbin/net/ddns_run.sh

Extracting sbin/dhcpreset.sh

Extracting sbin/net/dhcpsrv_run.sh

Extracting sbin/extra_app.sh

Extracting sbin/initap.sh

Extracting sbin/initap_normal.sh

Extracting sbin/initap_VFW.sh

Extracting sbin/pppoe/etc/ppp/ip-down.sh

Extracting sbin/pppoe/etc/ppp/ip-up.sh

Extracting sbin/iptables_rule.sh

Extracting sbin/killap.sh

Extracting sbin/net/nat_run.sh

Extracting sbin/reboot.sh

Extracting sbin/rerun.sh

Extracting sbin/reset2def.sh

Extracting sbin/restore.sh

Extracting sbin/net/snmpd_run.sh

Extracting sbin/sreset.sh

Extracting sbin/startup.sh

Extracting sbin/TC_QoS_Rule.sh

Extracting sbin/net/tc_run.sh

Extracting sbin/upgdef.sh

Extracting sbin/upgfirmw.sh

Extracting sbin/upgimgf.sh

Extracting sbin/upgkern.sh

Extracting sbin/net/upnpc_run.sh

Extracting sbin/net/upnpd_run.sh

Extracting wwwroot/English.txt

Extracting sbin/net-snmp/share/snmp/mibs/IP-MIB.txt

Extracting wwwroot/Japanese.txt

Extracting wwwroot/SChinese.txt

Extracting sbin/net-snmp/share/snmp/mibs/SNMPv2-CONF.txt

Extracting sbin/net-snmp/share/snmp/mibs/SNMPv2-MIB.txt

Extracting sbin/net-snmp/share/snmp/mibs/SNMPv2-SMI.txt

Extracting sbin/net-snmp/share/snmp/mibs/SNMPv2-TC.txt

Extracting sbin/net-snmp/share/snmp/mibs/SNMPv2-TM.txt

Extracting wwwroot/TChinese.txt

Extracting sbin/net-snmp/share/snmp/mibs/WELLTECH-MIB.txt

Extracting sbin/net-snmp/share/snmp/mibs/WELLTECH-NOTIFY-MIB.txt

Extracting sbin/cfgwgos.ini

Extracting sbin/db_bkupfile.ini

Extracting sbin/net/dhcpsrv.ini

Extracting sbin/net/DMZ.ini

Extracting sbin/emsclt.ini

Extracting sbin/gsmSMS.ini

Extracting sbin/net/IP_Filter.ini

Extracting sbin/net/MAC_Filter.ini

Extracting sbin/pk.ini

Extracting sbin/net/Port_Filter.ini

Extracting sbin/net/Port_Forward.ini

Extracting sbin/net/qos.ini

Extracting sbin/net/Service_Filter.ini

Extracting sbin/net/URL_Filter.ini

Extracting sbin/utelshell.ini

Extracting sbin/weekday.ini

Extracting wwwroot/img/Thumbs.db

Extracting lib/libdb-4.6.so

Extracting lib/libencrypt.so

Extracting lib/ld-uClibc.so.0

Extracting lib/libc.so.0

Extracting lib/libcrypt.so.0

Extracting lib/libdl.so.0

Extracting sbin/net/updatedd/libdyndns.so.0.0.0

Extracting lib/libm.so.0

Extracting lib/libnsl.so.0

Extracting lib/libpthread.so.0

Extracting lib/libresolv.so.0

Extracting lib/librt.so.0

Extracting lib/libutil.so.0

Extracting lib/494004ce3.580.08

Extracting lib/498004ce2.580.08

Extracting lib/libsrtp2.so.1

Extracting sbin/net/snmp.allow

Extracting sbin/net/web.allow

Extracting wwwroot/Device_status.asp.bak

Extracting sbin/dhcp.script.bak

Extracting sbin/emsclt.ini.bak

Extracting wwwroot/FlashTime.asp.bak

Extracting wwwroot/LineSetting_Modify.asp.bak

Extracting wwwroot/main_VFW.asp.bak

Extracting wwwroot/sip.asp.bak

Extracting wwwroot/SIPTrunk_Modify.asp.bak

Extracting wwwroot/SIPTrunk_New.asp.bak

Extracting sbin/net-snmp/share/snmp/mibs/WELLTECH-NOTIFY-MIB.txt.bak

Extracting sbin/pppoe/etc/ppp/pppoe.conf

Extracting sbin/net/snmpd.conf

Extracting sbin/net/udhcpd.conf

Extracting sbin/net/upnpd.conf

Extracting lib/modules/ac49x_dsp.ko

Extracting lib/modules/analog.ko

Extracting lib/modules/avalanche_cpmac.ko

Extracting lib/modules/avalanche_eswitch.ko

Extracting lib/modules/sched/cls_fw.ko

Extracting lib/modules/netfilter/ipt_CLASSIFY.ko

Extracting lib/modules/netfilter/ipt_CONNMARK.ko

Extracting lib/modules/netfilter/ipt_DSCP.ko

Extracting lib/modules/netfilter/ipt_layer7.ko

Extracting lib/modules/netfilter/ipt_MARK.ko

Extracting lib/modules/netfilter/ipt_string.ko

Extracting lib/modules/netfilter/ipt_tcpmss.ko

Extracting lib/modules/netfilter/ipt_tcpmssb.ko

Extracting lib/modules/netfilter/ipt_TOS.ko

Extracting lib/modules/ipv6.ko

Extracting lib/modules/netfilter/ip_conntrack_ftp.ko

Extracting lib/modules/netfilter/ip_conntrack_irc.ko

Extracting lib/modules/netfilter/ip_conntrack_tftp.ko

Extracting lib/modules/netfilter/ip_nat_ftp.ko

Extracting lib/modules/netfilter/ip_nat_irc.ko

Extracting lib/modules/netfilter/ip_nat_tftp.ko

Extracting lib/modules/sched/sch_cbq.ko

Extracting lib/modules/sched/sch_dsmark.ko

Extracting lib/modules/sched/sch_htb.ko

Extracting lib/modules/sched/sch_ingress.ko

Extracting lib/modules/sw_watchdog.ko

Extracting lib/modules/welltech_gpio.ko

Extracting sbin/l7-protocols/protocols/100bao.pat

Extracting sbin/l7-protocols/protocols/applejuice.pat

Extracting sbin/l7-protocols/protocols/ares.pat

Extracting sbin/l7-protocols/extra/audiogalaxy.pat

Extracting sbin/l7-protocols/protocols/bittorrent.pat

Extracting sbin/l7-protocols/protocols/directconnect.pat

Extracting sbin/l7-protocols/protocols/edonkey.pat

Extracting sbin/l7-protocols/protocols/fasttrack.pat

Extracting sbin/l7-protocols/protocols/ftp.pat

Extracting sbin/l7-protocols/protocols/gnutella.pat

Extracting sbin/l7-protocols/protocols/goboogy.pat

Extracting sbin/l7-protocols/extra/http-dap.pat

Extracting sbin/l7-protocols/extra/http-freshdownload.pat

Extracting sbin/l7-protocols/extra/http-itunes.pat

Extracting sbin/l7-protocols/protocols/http.pat

Extracting sbin/l7-protocols/extra/httpaudio.pat

Extracting sbin/l7-protocols/extra/httpcachehit.pat

Extracting sbin/l7-protocols/extra/httpcachemiss.pat

Extracting sbin/l7-protocols/extra/httpvideo.pat

Extracting sbin/l7-protocols/protocols/kugoo.pat

Extracting sbin/l7-protocols/protocols/msn-filetransfer.pat

Extracting sbin/l7-protocols/protocols/msnmessenger.pat

Extracting sbin/l7-protocols/protocols/poco.pat

Extracting sbin/l7-protocols/protocols/pop3.pat

Extracting sbin/l7-protocols/extra/pressplay.pat

Extracting sbin/l7-protocols/protocols/qq.pat

Extracting sbin/l7-protocols/extra/quicktime.pat

Extracting sbin/l7-protocols/protocols/rtp.pat

Extracting sbin/l7-protocols/protocols/sip.pat

Extracting sbin/l7-protocols/protocols/skypeout.pat

Extracting sbin/l7-protocols/protocols/skypetoskype.pat

Extracting sbin/l7-protocols/protocols/smtp.pat

Extracting sbin/l7-protocols/extra/snmp-mon.pat

Extracting sbin/l7-protocols/extra/snmp-trap.pat

Extracting sbin/l7-protocols/protocols/yahoo.pat

Extracting sbin/cacert.pem

Extracting sbin/cakey.pem

Extracting sbin/dhcp.script

Extracting sbin/l7-protocols/l7-protocols.spec

Extracting sbin/net/ddns.ini

Extracting sbin/net/snmpd.ini

Extracting s insmod software watchdog module is success

bin/net/tr069_run.sh

Extracting sbin/net/udhcpd.leases

Extracting sbin/net/upnpd.ini

Directory wwwroot/lib

Directory wwwroot/img

Directory wwwroot

Directory var

Directory sbin/pppoe/usr/sbin

Directory sbin/pppoe/usr

Directory sbin/pppoe/etc/ppp

Directory sbin/pppoe/etc

Directory sbin/pppoe

Directory sbin/net/updadsp device 0 memory at block 17c00000

tedd

Directory sbin/net/linuxigd

Directory sbin/net-snmp/share/snmp/mibs

Directory sbin/net-snmp/share/snmp

Directory sbin/net-snmp/share

Directory sbin/net-snmp

Directory sbin/net

Directory sbin/l7-protocols/protocols

Directory sbin/l7-protocols/extra

Directory sbin/l7-protocols

Directory sbin

Directory lib/modules/sched

Directory lib/modules/netfilter

Directory lib/modules

Directory lib

Everything is Ok

chdir CWD=/config_fs.

Extracted /config_fs/wg28.1.01e.bin (size=2821244).

*** Primary is OK ***.

*** Firmware=wg28.1.01e.bin ***.

fwmgr 1.0.0 (R091217) for wg25xx, PPID=75, PID=85, exit.

welltech_gpio: module license 'Welltech Computer LTD.' taints kernel.

insmod gpio module success

start to init_gpio

end to init_gpio

Main Board is : WG49408_V01

Telephony thread started

insmod analog module success v1.0

Sync BerkDB to DBINI now...

shmat: id 655379: unable to attach to shared system memory region: Invalid argument \/wg25_24/public/db/BerkeleyDB.c 2635

Algorithmics/MIPS FPU Emulator v1.5

00:00:45 cfgwgP00124 main L00204 1.0.0 (R170520.0931), PPID=87, PID=124, start.

00:00:45 cfgwgP00124 main L00224 Set FwPrefix=wg25.

00:00:45 cfgwgP00124 main L00234 Set MachType=4 WG25XX.

00:00:45 cfgwgP00124 main L00247 ProgConf=./cfgwgos.ini.

00:00:45 cfgwgP00124 BDbGetStr L00418 BerkDb_Get ipv6=0.

00:00:45 cfgwgP00124 _InsMod L01824 BDbGetStr IPv6=0.

00:00:45 cfgwgP00124 _InsMod L01838 Set IPv6=0 v4.

00:00:45 cfgwgP00124 BDbGetStr L00418 BerkDb_Get lanmode=1.

00:00:45 cfgwgP00124 _InsMod L01859 BDbGetStr LANMode=1.

00:00:45 cfgwgP00124 _InsMod L01881 Set LANMode=1 NAT.

00:00:45 cfgwgP00124 InsDfltMod L01758 ifconfig esw0 down

SIOCGIFFLAGS: No such device

00:00:45 cfgwgP00124 InsDfltMod L01762 rmmod avalanche_eswitch

rmmod: avalanche_eswitch: Success

00:00:45 cfgwgP00124 InsDfltMod L01766 insmod "/lib/modules/avalanche_cpmac.ko"

Error getting CPMAC Configuration params for instance:0

Environment Variable:MACCFG_A not set in bootloader

Setting Default configuration params for CPMAC instance:0

MAC CFG : Tx Interrupts off , threshold : 20

flag changed to have all multicast IFF_MULTICAST | IFF_BROADCAST | IFF_ALLMULTI

Error getting CPMAC Configuration params for instance:1

Environment Variable:MACCFG_B not set in bootloader

Setting Default configuration params for CPMAC instance:1

MAC CFG : Tx Interrupts off , threshold : 20

flag changed to have all multicast IFF_MULTICAST | IFF_BROADCAST | IFF_ALLMULTI

TI CPMAC Linux DDA version 2.0 - CPMAC DDC version 0.3

Cpmac: Installed 2 instances.

Cpmac driver is allocating buffer memory at init time.

00:00:45 cfgwgP00124 InsDfltMod L01771 Set WAN=eth0, LAN=eth1

00:00:45 cfgwgP00124 InsDfltMod L01802 rmmod ipv6

rmmod: ipv6: Success

00:00:46 cfgwgP00124 ReadProgCo L00332 [SYSTEM].

00:00:46 cfgwgP00124 ReadProgCo L00337 PIDPath=/var/pidfile.

00:00:46 cfgwgP00124 ReadProgCo L00348 [IP_CHG].

00:00:46 cfgwgP00124 ReadProgCo L00370 PIDFile01=/var/pidfile/emsclt.pid.

00:00:46 cfgwgP00124 ReadProgCo L00370 PIDFile02=/var/pidfile/SipMgr.pid.

00:00:46 cfgwgP00124 ReadProgCo L00370 PIDFile03=/var/pidfile/phoneMgr.pid.

00:00:46 cfgwgP00124 IfAddr L01569 ifconfig lo 127.0.0.1

00:00:46 cfgwgP00124 IfAddr L01574 ifconfig eth1 up

00:00:46 cfgwgP00124 IfAddr L01579 ifconfig eth0 up

00:00:46 cfgwgP00124 _IfAddr L01389 KillPID "/var/pidfile/udhcpc.pid", Ret=-1.

00:00:46 cfgwgP00124 _IfAddr L01391 KillPIDPPPoE Ret=3.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get dns1=168.95.1.1.

00:00:46 cfgwgP00124 SetDNS L00526 BDbGetStr DNS1=168.95.1.1.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get dns2=168.192.1.12.

00:00:46 cfgwgP00124 SetDNS L00539 BDbGetStr DNS2=168.192.1.12.

00:00:46 cfgwgP00124 SetDNS L00547 Opened "/etc/resolv.conf".

00:00:46 cfgwgP00124 SetDNS L00565 Wrote "nameserver 168.95.1.1

".

00:00:46 cfgwgP00124 SetDNS L00565 Wrote "nameserver 168.192.1.12

".

00:00:46 cfgwgP00124 BDbPutStr L00468 BerkDb_Put ueip=.

00:00:46 cfgwgP00124 _IfAddr L01422 BDbPutStr UEIP=.

00:00:46 cfgwgP00124 _IfAddr L01425 WANv6=eth0, LANv6=eth1.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get ipalan=192.168.123.123.

00:00:46 cfgwgP00124 _SetLIP L00812 BDbGetStr IPA_LAN=192.168.123.123.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get ipmlan=255.255.255.0.

00:00:46 cfgwgP00124 _SetLIP L00829 BDbGetStr IPM_LAN=255.255.255.0.

00:00:46 cfgwgP00124 DelDefGws L02006 route del default gw 0.0.0.0 dev eth1

route: SIOC[ADD|DEL]RT: No such process

00:00:46 cfgwgP00124 _SetLIP L00849 ifconfig eth1 inet 192.168.123.123 netmask 255.255.255.0

00:00:46 cfgwgP00124 DelIfINet6 L02039 ERR: GetIfINet6s ErrNo=2.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get dhcp=0.

00:00:46 cfgwgP00124 _IfAddr L01445 BDbGetStr DHCP=0.

00:00:46 cfgwgP00124 _IfAddr L01459 Set DHCP=0 FixedIP.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get ipa=10.1.1.3.

00:00:46 cfgwgP00124 _SetIP L00629 BDbGetStr IPA=10.1.1.3.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get ipm=255.255.255.0.

00:00:46 cfgwgP00124 _SetIP L00646 BDbGetStr IPM=255.255.255.0.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get ipgw=10.1.1.254.

00:00:46 cfgwgP00124 _SetIP L00658 BDbGetStr IPGw=10.1.1.254.

00:00:46 cfgwgP00124 BDbGetStr L00418 BerkDb_Get vlan=0.

00:00:46 cfgwgP00124 SetVLAN L00395 BDbGetStr VLAN=0.

00:00:46 cfgwgP00124 DelDefGws L02006 route del default gw 0.0.0.0 dev eth0

route: SIOC[ADD|DEL]RT: No such process

00:00:46 cfgwgP00124 _SetIP L00678 ifconfig eth0 inet 10.1.1.3 netmask 255.255.255.0

00:00:46 cfgwgP00124 AddDefGw L01990 route add default gw 10.1.1.254 dev eth0

00:00:46 cfgwgP00124 DelIfINet6 L02039 ERR: GetIfINet6s ErrNo=2.

00:00:47 cfgwgP00124 _IfAddr L01554 Sent Sig(51 IPChg). Cntr=0.

00:00:47 cfgwgP00124 AtExit L00264 1.0.0 (R170520.0931), PPID=87, PID=124, exit.

sh: Can't open /config_fs/net/vgcps_run.sh

pk 1.0.0 (R170520.0931), PPID=157, PID=158, start.

Max Line = 32 and Max_URI_LEN=size(128)

g_Config.bEncrypt=0

[SipMgr] Get Local IPv4:0 IPv6:0

Eth_Name=eth0, Localv4IP=10.1.1.3, Localv6IP=

killall: udhcpd: no process killed

0

1

maxreg=20

maxtransc=104

maxsub=12

maxcallleg=72

udhcp server (v0.9.8) started

GeneralPoolNumofPages=403

killall: snmpd: no process killed

killall: upnpd: no process killed

[PhoMgr] waiting for get local ip ......

[PhoMgr] got local ip4=10.1.1.3, ip6=, NIC=eth0, base=eth0

DSP device download : file size is 262820..

Initializing vlynq

starting vlynq_vdsp configuration...

Init SOC to 498(1) start

Init SOC to 498(1) end

passed

DSP device 0, download a 4 channels DSP firmware..passed, ret=1

DSP device download : file size is 245968..

DSP device 1, download a 4 channels DSP firmware..passed, ret=1

Do download firmware for dev:1 Done

dspsetdefault okDSP device 0, SetupDevice...passed

DSP device 1, SetupDevice...passed

dspsetdevice ok (MAX_PHONE_CHN:8)

dsp openchannel ok

end do Dsp_Init

[PhoMgr] Try Hardware SPI.

start to tele_reset

DSP is active.

tele_reset test DSP_RESET_DSBL_CTRL 1

tele_reset test DSP_RESET_DSBL_CTRL 2 7fb

tele_reset test DSP_RESET_DSBL_CTRL 3 7fb

end to tele_reset

DSP-TELE: SPCR1 reg value = 0x10800FF .

DSP-TELE: Telephony Interface driver installed.

Use Hardware SPI.

xxxxxxxxxxxxxxxxxonEvt_BoardStop,eEvt_Dev_BoardStop=41,../../src/DeviceMgr.c,onEvt_BoardStop,561

[PhoMgr] send reg SipTrk=0, px=10.1.1.2, TelNo=1000

Start to DetectVenderBoard

Try Detect Silicon Lab si3215

line = 0 Reg0 = 03

line = 0 Reg8 = 02

line = 0 Reg11 = 33

line = 0 Reg64 = 00

Detection Phyical Line 0 Mapping to Logic_line 0 FXS is SiliconLab's SLIC

line = 0 Reg0 = 03

line = 0 Reg8 = 02

line = 0 Reg11 = 33

line = 0 Reg64 = 00

SLIC initialization starting for line 0

starting the DC calibration phase 1 for line 0

starting the DC calibration phase 2 for line 0

starting slic calibration for line 0, reg96: 71, reg97: 30

[SNTP] waiting for get local ip ......

[SNTP] got local ip=10.1.1.3, NIC=eth0

[SNTP] srv=[168.95.195.12], dur=43200, TZ=nan, DayLightEnable=0, DL-bias=0

starting manual calibration phase 1for line 0

starting manual calibration phase 2for line 0

starting slic calibration for line 0, reg96: 64, reg97: 1

00:00:58 utelnetdP00257 L02240 Semaphore_Create SemKeyDUGRqst=0x0000086b.

00:00:58 utelnetdP00257 L02250 ShareMem_Create ShMKeyDUGRqst=0x0000076b, cbShm=64.

00:00:58 utelnetdP00258 L00817 sigaction(50 SigApplyChg).

00:00:58 utelnetdP00258 L00817 sigaction(51 SigIPChg).

00:00:58 utelnetdP00258 L00817 sigaction(53 SigDUGRqst).

00:00:58 utelnetdP00258 L00827 1.0.0 (R170520.0931), PPID=257, PID=258, start.

00:00:58 utelnetdP00258 L00841 WrPID PIDFile=/var/pidfile/utelnetd.pid.

telnetd: starting

port: 23; interface: any; login program: .Starting set direct register for line 0

/utelshell

00:00:58 utelnetdP00258 L01652 socket AF_INET FD=3.

00:00:58 utelnetdP00258 L01714 Starting to initialize indirect register 22-26 for line 0

listen 0.0.0.0 (23), FD=3.

00:00:58 utelnetdP00258 L00984 (port: 23, ifname: any, login: ./utelshell) startup succeeded.

successed initialized for line 0

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 0 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 0 setting interrupt mode!!

line 0 : SLIC reset ok!!

Try Detect Silicon Lab si3215

line = 1 Reg0 = 03

line = 1 Reg8 = 02

line = 1 Reg11 = 33

line = 1 Reg64 = 00

Detection Phyical Line 1 Mapping to Logic_line 1 FXS is SiliconLab's SLIC

line = 1 Reg0 = 03

line = 1 Reg8 = 02

line = 1 Reg11 = 33

line = 1 Reg64 = 00

SLIC initialization starting for line 1

starting the DC calibration phase 1 for line 1

starting the DC calibration phase 2 for line 1

starting slic calibration for line 1, reg96: 71, reg97: 30

starting manual calibration phase 1for line 1

get mac addr ioctl:No such device [esw0]

DDNS is disabled

Run Extra application!!!!!!

Runngin well ...................

starting manual calibration phase 2for line 1

Run Extra application!!!!!!

Runngin well ...................

Everything running Well

Please press Enter to activate this console. starting slic calibration for line 1, reg96: 64, reg97: 1

Starting set direct register for line 1

Starting to initialize indirect register 22-26 for line 1

successed initialized for line 1

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 1 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 1 setting interrupt mode!!

line 1 : SLIC reset ok!!

Try Detect Silicon Lab si3215

line = 2 Reg0 = 03

line = 2 Reg8 = 02

line = 2 Reg11 = 33

line = 2 Reg64 = 00

Detection Phyical Line 2 Mapping to Logic_line 2 FXS is SiliconLab's SLIC

line = 2 Reg0 = 03

line = 2 Reg8 = 02

line = 2 Reg11 = 33

line = 2 Reg64 = 00

SLIC initialization starting for line 2

starting the DC calibration phase 1 for line 2

starting the DC calibration phase 2 for line 2

starting slic calibration for line 2, reg96: 71, reg97: 30

starting manual calibration phase 1for line 2

starting manual calibration phase 2for line 2

starting slic calibration for line 2, reg96: 64, reg97: 1

Starting set direct register for line 2

Starting to initialize indirect register 22-26 for line 2

successed initialized for line 2

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 2 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 2 setting interrupt mode!!

line 2 : SLIC reset ok!!

Try Detect Silicon Lab si3215

line = 3 Reg0 = 03

line = 3 Reg8 = 02

line = 3 Reg11 = 33

line = 3 Reg64 = 00

Detection Phyical Line 3 Mapping to Logic_line 3 FXS is SiliconLab's SLIC

line = 3 Reg0 = 03

line = 3 Reg8 = 02

line = 3 Reg11 = 33

line = 3 Reg64 = 00

SLIC initialization starting for line 3

starting the DC calibration phase 1 for line 3

starting the DC calibration phase 2 for line 3

starting slic calibration for line 3, reg96: 71, reg97: 30

starting manual calibration phase 1for line 3

starting manual calibration phase 2for line 3

starting slic calibration for line 3, reg96: 64, reg97: 1

Starting set direct register for line 3

Starting to initialize indirect register 22-26 for line 3

successed initialized for line 3

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 3 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 3 setting interrupt mode!!

line 3 : SLIC reset ok!!

Try Detect Silicon Lab si3215

line = 4 Reg0 = 03

line = 4 Reg8 = 02

line = 4 Reg11 = 33

line = 4 Reg64 = 00

Detection Phyical Line 4 Mapping to Logic_line 4 FXS is SiliconLab's SLIC

line = 4 Reg0 = 03

line = 4 Reg8 = 02

line = 4 Reg11 = 33

line = 4 Reg64 = 00

SLIC initialization starting for line 4

starting the DC calibration phase 1 for line 4

starting the DC calibration phase 2 for line 4

starting slic calibration for line 4, reg96: 71, reg97: 30

starting manual calibration phase 1for line 4

starting manual calibration phase 2for line 4

starting slic calibration for line 4, reg96: 64, reg97: 1

Starting set direct register for line 4

Starting to initialize indirect register 22-26 for line 4

successed initialized for line 4

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 4 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 4 setting interrupt mode!!

line 4 : SLIC reset ok!!

Try Detect Silicon Lab si3215

line = 5 Reg0 = 03

line = 5 Reg8 = 02

line = 5 Reg11 = 33

line = 5 Reg64 = 00

Detection Phyical Line 5 Mapping to Logic_line 5 FXS is SiliconLab's SLIC

line = 5 Reg0 = 03

line = 5 Reg8 = 02

line = 5 Reg11 = 33

line = 5 Reg64 = 00

SLIC initialization starting for line 5

starting the DC calibration phase 1 for line 5

starting the DC calibration phase 2 for line 5

starting slic calibration for line 5, reg96: 71, reg97: 30

starting manual calibration phase 1for line 5

starting manual calibration phase 2for line 5

starting slic calibration for line 5, reg96: 64, reg97: 1

Starting set direct register for line 5

Starting to initialize indirect register 22-26 for line 5

create shm queue success

userName=root userPass=root

userName2=admin userPass2=admin

userName3=user userPass3=user

successed initialized for line 5

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 5 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 5 setting interrupt mode!!

line 5 : SLIC reset ok!!

Try Detect Silicon Lab si3215

line = 6 Reg0 = 03

line = 6 Reg8 = 02

line = 6 Reg11 = 33

line = 6 Reg64 = 00

Detection Phyical Line 6 Mapping to Logic_line 6 FXS is SiliconLab's SLIC

line = 6 Reg0 = 03

line = 6 Reg8 = 02

line = 6 Reg11 = 33

line = 6 Reg64 = 00

SLIC initialization starting for line 6

starting the DC calibration phase 1 for line 6

starting the DC calibration phase 2 for line 6

starting slic calibration for line 6, reg96: 71, reg97: 30

starting manual calibration phase 1for line 6

00:01:09 emscltP00276 L01416 Semaphore_Create STATE_INFO_SEMAPHORE_KEY=0x00000866.

00:01:09 emscltP00276 L01429 ShareMem_Create STATE_INFO_SHM_KET=0x00000766, cbShm=7440.

00:01:09 emscltP00276 L01438 Write Firmware Name --> (wg28.1.01e.bin) (wg28.1.01e.bin).

00:01:09 emscltP00276 L00154 Semaphore_Create SemKeyDUGRqst=0x0000086b.

00:01:09 emscltP00276 L00167 ShareMem_Create ShMKeyDUGRqst=0x0000076b, cbShm=64.

00:01:09 emscltP00279 L00207 sigaction(50 SigApplyChg).

00:01:09 emscltP00279 L00207 sigaction(51 SigIPChg).

00:01:09 emscltP00279 L00207 sigaction(52 ).

00:01:09 emscltP00279 L00207 sigaction(53 SigDUGRqst).

00:01:09 emscltP00279 L00207 sigaction(54 ).

cat: /config_fs/net/emscltRebootCount.ini: No such file or directory

00:01:09 emscltP00279 L00254 1.0.0 (R170520.0931) for wg28, PPID=1, PID=279, iRebootCount=0 start.

00:01:09 emscltP00279 L00774 Set FwPrefix=wg28.

00:01:09 emscltP00279 L00792 Set MachType=6 WG28XX.

autoua=0

szUaPrefix=Wildix W04FXS 25.1.0209d

00:01:09 emscltP00279 L00240 ProvType=0 None.

00:01:09 emscltP00279 L00269 Set DHCP=0 FixedIP.

00:01:09 emscltP00279 L00290 Set VLAN=0.

00:01:09 emscltP00279 L00323 Set LANMode=1 NAT.

00:01:09 emscltP00279 L00334 Set WAN=eth0, LAN=eth1.

00:01:09 emscltP00279 L00095 HTTPURL=.

00:01:09 emscltP00279 L00114 HTTPCRI=1440.

00:01:09 emscltP00279 L00139 HTTPCF=1.

starting manual calibration phase 2for line 6

starting slic calibration for line 6, reg96: 64, reg97: 1

Starting set direct register for line 6

Starting to initialize indirect register 22-26 for line 6

successed initialized for line 6

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 6 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 6 setting interrupt mode!!

line 6 : SLIC reset ok!!

Try Detect Silicon Lab si3215

line = 7 Reg0 = 03

line = 7 Reg8 = 02

line = 7 Reg11 = 33

line = 7 Reg64 = 00

Detection Phyical Line 7 Mapping to Logic_line 7 FXS is SiliconLab's SLIC

line = 7 Reg0 = 03

line = 7 Reg8 = 02

line = 7 Reg11 = 33

line = 7 Reg64 = 00

SLIC initialization starting for line 7

starting the DC calibration phase 1 for line 7

starting the DC calibration phase 2 for line 7

starting slic calibration for line 7, reg96: 71, reg97: 30

starting manual calibration phase 1for line 7

starting manual calibration phase 2for line 7

starting slic calibration for line 7, reg96: 64, reg97: 1

Starting set direct register for line 7

Starting to initialize indirect register 22-26 for line 7

successed initialized for line 7

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-589 SLIC 7 setting interrupt mode!!

drivers/char/analog/silab/si3215.c-SILICONLAB_SLIC_reset-590 SLIC 7 setting interrupt mode!!

line 7 : SLIC reset ok!!

hwConfig[0].logic_port 0

hwConfig[0].type 1

hwConfig[1].logic_port 1

hwConfig[1].type 1

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:0)(nType:1)

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:1)(nType:1)

hwConfig[2].logic_port 2

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:2)(nType:1)

hwConfig[2].type 1

hwConfig[3].logic_port 3

hwConfig[3].type 1

hwConfig[4].logic_port 4

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:3)(nType:1)

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:4)(nType:1)

hwConfig[4].type 1

hwConfig[5].logic_port 5

hwConfig[5].type 1

hwConfig[6].logic_port 6

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:5)(nType:1)

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:6)(nType:1)

hwConfig[6].type 1

hwConfig[7].logic_port 7

hwConfig[7].type 1

xxxxxxxxxxxxxxxxxxxxxonEvt_ChnDetect,eEvt_Dev_ChnDetect=40,../../src/DeviceMgr.c,onEvt_ChnDetect,552

====================onEvDev_ChnDetect,../../src/PhoneMgr.c,onEvDev_ChnDetect,6486 (nChan:7)(nType:1)

[PhoMgr] Hardware SPI OK

start polling active......

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Ring Value reset ok!!

Starting pid 273, console /dev/console: '/bin/sh'

BusyBox v1.2.2 (2009.12.18-02:00+0000) Built-in shell (ash)

Enter 'help' for a list of built-in commands.

#

ifconfig

# ifconfig

eth0 Link encap:Ethernet HWaddr 00:01:A8:0B:68:F4

inet addr:10.1.1.3 Bcast:10.255.255.255 Mask:255.255.255.0

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:5532 errors:39 dropped:0 overruns:0 frame:0

TX packets:1240 errors:0 dropped:0 overruns:0 carrier:0

collisions:60 txqueuelen:1000

RX bytes:472703 (461.6 KiB) TX bytes:269390 (263.0 KiB)

eth1 Link encap:Ethernet HWaddr 00:01:A8:0B:68:F3

inet addr:192.168.123.123 Bcast:192.168.123.255 Mask:255.255.255.0

UP BROADCAST MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

Base address:0x800

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0

UP LOOPBACK RUNNING MTU:16436 Metric:1

RX packets:636 errors:0 dropped:0 overruns:0 frame:0

TX packets:636 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:295895 (288.9 KiB) TX bytes:295895 (288.9 KiB)

#

eth0 จะเป็นพอร์ต WAN
eth1 พอร์ต LAN

ps

# ps -l

PID Uid VmSize Stat Command

1 0 160 S init

2 0 SW [ksoftirqd/0]

3 0 SW< [desched/0]

4 0 SW< [events/0]

5 0 SW< [khelper]

10 0 SW< [kthread]

13 0 SW< [kblockd/0]

33 0 SW [pdflush]

34 0 SW [pdflush]

36 0 SW< [aio/0]

35 0 SW [kswapd0]

47 0 SW [mtdblockd]

69 0 SW< [IRQ 8]

72 0 SW< [IRQ 15]

79 0 SWN [jffs2_gcd_mtd2]

95 0 SW< [IRQ 14]

94 0 RW [watchdog]

110 0 RW [analog]

135 0 SW< [IRQ 41]

138 0 SW< [IRQ 27]

151 0 428 S ./pk

177 0 540 S ./deviceMgr

186 0 3576 S ./SipMgr

187 0 3576 S ./SipMgr

188 0 3576 S ./SipMgr

189 0 3576 S ./SipMgr

190 0 3576 S ./SipMgr

209 0 304 S udhcpd

239 0 1288 S ./phoneMgr

240 0 1288 S ./phoneMgr

241 0 1288 S ./phoneMgr

242 0 1288 S ./phoneMgr

243 0 1288 S ./phoneMgr

245 0 632 S ./sntp

248 0 528 S ./utelnetd

251 0 572 R N ./logmgr

266 0 312 S -sh

268 0 1172 S ./webs

272 0 1112 S ./emsclt

315 0 164 R ps -l

#

netstat

# netstat -l

Active Internet connections (only servers)

Proto Recv-Q Send-Q Local Address Foreign Address State

tcp 0 0 *:80 *:* LISTEN

tcp 0 0 *:23 *:* LISTEN

tcp 0 0 *:443 *:* LISTEN

netstat: no support for `AF INET6 (tcp)' on this system.

udp 0 0 10.1.1.3:8080 *:*

udp 0 0 *:67 *:*

netstat: no support for `AF INET6 (udp)' on this system.

netstat: no support for `AF INET6 (raw)' on this system.

Active UNIX domain sockets (only servers)

Proto RefCnt Flags Type State I-Node Path

จะเห็นว่ามีการเปิดพอร์ต 80, 443 สำหรับ Web Server และเปิดพอร์ต 23 สำหรับ Telnet ครับ

File system

# df -h

Filesystem Size Used Available Use% Mounted on

/dev/mtdblock0 732.0k 732.0k 0 100% /

/dev/mtdblock2 13.0M 6.3M 6.7M 48% /config_fs

# mount

/dev/root on / type cramfs (ro)

proc on /proc type proc (rw,nodiratime)

/dev/mtdblock2 on /config_fs type jffs2 (rw,noatime)

ramfs on /apps type ramfs (rw)

devpts on /dev/pts type devpts (rw)

#

mtdblock2 มีพื้นที่เหลืออีกเกือบ 7 MB ที่สามารถเขียนข้อมูลลงไปและไม่หายถ้าปิดเครื่อง เพราะว่า mount file system แบบ jffs2

top

Mem: 26604K used, 35732K free, 0K shrd, 316K buff, 18060K cached

Load average: 1.00 1.00 0.94 (Status: S=sleeping R=running, W=waiting)

PID USER STATUS RSS PPID %CPU %MEM COMMAND

320 0 R 196 266 0.9 0.3 exe

186 0 S 3576 1 0.0 5.7 SipMgr

188 0 S 3576 187 0.0 5.7 SipMgr

187 0 S 3576 186 0.0 5.7 SipMgr

189 0 S 3576 187 0.0 5.7 SipMgr

190 0 S 3576 187 0.0 5.7 SipMgr

239 0 S 1288 1 0.0 2.0 phoneMgr

241 0 S 1288 240 0.0 2.0 phoneMgr

240 0 S 1288 239 0.0 2.0 phoneMgr

242 0 S 1288 240 0.0 2.0 phoneMgr

243 0 S 1288 240 0.0 2.0 phoneMgr

268 0 S 1172 1 0.0 1.8 webs

272 0 S 1112 1 0.0 1.7 emsclt

245 0 S 632 1 0.0 1.0 sntp

251 0 R N 572 1 0.0 0.9 logmgr

177 0 S 540 1 0.0 0.8 deviceMgr

248 0 S 528 1 0.0 0.8 utelnetd

151 0 S 428 1 0.0 0.6 pk

266 0 S 312 1 0.0 0.4 sh

209 0 S 304 1 0.0 0.4 udhcpd

1 0 S 160 0 0.0 0.2 init

RAM ใช้ไปประมาณ 27 MB ยังเหลือ RAM ให้ใช้งานอื่นอีกราว 33 MB ครับ

cpuinfo

# cat /proc/cpuinfo

system type : Texas Instruments BroadBand SoC

processor : 0

cpu model : MIPS 4KEc V4.8

BogoMIPS : 162.20

wait instruction : yes

microsecond timers : yes

tlb_entries : 16

extra interrupt vector : yes

hardware watchpoint : yes

VCED exceptions : not available

VCEI exceptions : not available

#

mtd

# cat /proc/mtd

dev: size erasesize name

mtd0: 00060000 00020000 "mtd0"

mtd1: 00100000 00020000 "mtd1"

mtd2: 00d00000 00020000 "mtd2"

mtd3: 00080000 00020000 "mtd3"

mtd4: 00080000 00020000 "mtd4"

mtd5: 00020000 00020000 "mtd5"

mtd6: 00100000 00020000 "mtd6"

#

Flash Layout

MTD Flash Layout

ไฟล์ของ mtd กดโหลดที่ลิงค์ด้านล่างครับ
https://www.4shared.com/rar/3T2HOgcWca/mtd.html

วันอาทิตย์ที่ 11 มีนาคม พ.ศ. 2561

PLANET VIP-157S v5 Teardown

สวัสดีครับ วันนี้ผมจะมาแกะตัวอุปกรณ์ Analog Telephone Adapter หรือที่เรียกย่อกันว่า ATA ให้ดูกันนะครับ

ตัวอุปกรณ์

ตัวกล่องก็จะมีขนาดเล็กๆ กระทัดรัดโดยพอร์ตต่างๆ อยู่ด้านข้างครับ ก็จะมีพอร์ต LAN, PC, PHONE1, PHONE2, ปุ่ม Reset ครับ การแกะก็ถอดน็อตข้างล่างเพียงตัวเดียว

ภายในกล่อง

แกะออกมาก็จะเจอบอร์ด 2 บอร์ดประกบเชื่อมต่อกันอยู่ครับ เรามาดูบอร์ดแรกที่อยู่ข้างล่างกันก่อนนะครับ

บอร์ดข้างล่าง

บอร์ดนี้ก็จะมี SoC, ชิป LAN อยู่ครับ ทางขวามือของรูปจะมีพอร์ต Serial อยู่ครับ ความเร็วจะเป็น 57600 bps โหมด 8 bit, No Parity, 1 Stop bit ครับ เรามาดูรายละเอียดของชิปแต่ละตัวกันต่อเลยครับ

CM5000LF

Crystal Media CM5000LF --> Voice Over IP CPE Processor ตัวนี้เป็นหน่วยประมวณผลหลัก ข้างในมี CPU Core MIPS R3000 ครับ

IP175D

IC+ IP175D --> 5 Port 10/100 Ethernet Integrated Switch

A1526 (AT1526)

AT1526 --> 1MHz, All-Ceramic, 2A PWM Buck DC/DC Converter ใช้แปลงไฟ DC to DC ครับ

MSC 7102

Microsemi NX7102IDE --> 3A High Voltage Synchronous Buck Converter

ต่อมาก็พลิกดูอีกด้านนนะครับ

บอร์ดล่างด้านใต้

ด้านใต้มีชิป RAM, ROM อยู่ครับ

29LV160DTTI

MXIC 29LV160DTTI --> 16M-BIT [2M x 8 / 1M x 16] 3V SUPPLY FLASH MEMORY ตัวนี้เป็น Flash ROM ขนาด 2 MB ครับ

W9812G6KH-6

winbond W9812G6KH --> ตัวนี้เป็น SDRAM ขนาด 16 MB ครับ

ต่อมาก็จะเป็นบอร์ดอีกตัวที่อยู่ด้านบนนะครับ

บอร์ดตัวบน

ก็จะเห็นมีชิปหลักๆ อยู่ตัวเดียวเลยครับ

le88266TQC

ZARLINK Le88266TQC --> Dual Channel Wideband Auto Battery Switching (ABS) VoicePort™ ตัวนี้เป็น Subscriber line interface card (SLIC) ใช้ไดรสัญญาณของโทรศัพท์บ้านครับ

1089QB

BOURNS TISP61089QB --> PROGRAMMABLE OVERVOLTAGE PROTECTOR QUAD FORWARD-CONDUCTING P-GATE THYRISTOR

6426

CET CEA6426 --> N-Channel Enhancement Mode Field Effect Transistor

พลิกดูอีกด้านก็จะเป็นด้านบนที่มี LED แสดงผลอยู่ครับ

บอร์ดบน

ต่อมาก็เป็น Boot log ของอุปกรณ์ที่ได้จากพอร์ต Serial ครับ User name มีสองตัวนะครับ

User: root, Password: ว่าง
User: superuser, Password: 1234321

start RAM test

SDRAM SIZE: 16M!

vBOOTMain()

move gunzip ROM image to RAM

jump to gunzip RAM image

Boot Code Not Support Dual-Code!

press 'ENTER' to load IC.GZ within 3 seconds

otherwise, decompress VOIP image

Boot Code Version(2M): 2013-04-09 (lzma)

...

Loading VOIP0.GZ to RAM

...............................................

Memory used=0x00004000

Ready to run..........

SBD RESET COMPLETE !

===== start of 16M uCos ====

OSInit done

OS start

HeapStart=0x80b12a00,HeapEnd=0x80de0000,memory size=2938368

OSStatInit()

database init

Size of database=0x00006a94

Size of PhoneBook=0x00006504

Size of Call Log=0x00004404

# Read phone book !

Read data_base from flash!

# (WEB Port=80)

# Last UpdateDate=

# (CPU Ver=130422)

# (DSP Ver=1203150)

# (MAC= 00:30:4F:BB:F7:FA)

customId : 0

customManufacturer : CMI

customManufacturerOui : 001A00

customModelName : IP Phone

customDescription : IP Phone

customProductClass : VoIP

customSerialNumber :

customHwVersion : 1.0.0

customSwVersion : VIP-157 V5.0

customFwVersion : VIP-157 V5.0

customHwVersion2 : 1.0.0

customSwVersion2 : 1.0.0

customSpecVersion : 1.0.0

Load dsp code

ethTask0 Active,stack=0x80aaaa00

ethTask1 Active,stack=0x80aaea00

language is the same!!!!

WebSystemInfo.language = 0

crystal_port=65535

net init

DNS Init!

DNS Timer Init!

tftp client init

http server init

telnet server init

tcli init

sStartcodecUi(): codecUi init

vCrystalInit()

dsp init

launch_DHCPv4 sockfd=0, msg_fd=37 ,Id=1!

launch_Httpv4_listener(): Id-fd=2-3

=== launch_DHCPv4 server fail : eDhcp4Server=0 ===

=== launch_crystal_ND=38 , Id=3! ===

=== launch_DHCPv6 server fail : eDhcp6Server=0 ===

======= start_session_sched()=======

Get Mib data at mib_out.c, addr=0x8055f7d8

---------- read_context_database ---------

ID_STATE: my_context1 .1.3.6.1.2.1.5.1.0

IDENTITY_STATE:my_context1 contextid=VIEW_STATE: 1 Null currentTime

view=1

PROXY_STATE: 0 0 0

context_createEntry():contextIDLen=9

ID_STATE: my_context2 .1.3.6.1.4.1.535.1.1.2.4.9.0

IDENTITY_STATE:my_context2 contextid=VIEW_STATE: 2 Null currentTime

view=2

PROXY_STATE: 0 0 0

context_createEntry():contextIDLen=13

context_createEntry():contextIDLen=14

size of (vCLIEntryPoint()'s sEntry)=43672(10918)

context: name=noAuthContext ,idlen=14

context: name=my_context2 ,idlen=13

Macth contex: name=my_context2 ,idlen=13

slic init--StartSLIC

Slic Device0 Initialized in MPI 3-Wire Mode

Slic test OK!--Run_SLIC_Task

SLIC Ready,stack=0x80a4cdb0->0x80a4edac--Run_SLIC_Task

Run_CodecUi_Fun():

Phone Task is running!

*************************

*** IaInitAllocator() ***

*************************

udp6SelectTos(0, 0)

udpSetSockOpt(m_hUdpsock=0, trafficClass=0)

udp6SelectTos(1, 0)

udpSetSockOpt(m_hUdpsock=1, trafficClass=0)

>>> CDUdpStack::bind(m_hUdpsock=0) port=43210 <<<

>>> CDUdpStack::bind(m_hUdpsock=1) port=43211 <<<

udp6SelectTos(2, 0)

udpSetSockOpt(m_hUdpsock=2, trafficClass=0)

udp6SelectTos(3, 0)

udpSetSockOpt(m_hUdpsock=3, trafficClass=0)

udp6SelectTos(4, 0)

udpSetSockOpt(m_hUdpsock=4, trafficClass=0)

udp6SelectTos(5, 0)

udpSetSockOpt(m_hUdpsock=5, trafficClass=0)

udp6SelectTos(6, 0)

udpSetSockOpt(m_hUdpsock=6, trafficClass=0)

>>> CDUdpStack::bind(m_hUdpsock=2) port=7005 <<<

>>> CDUdpStack::bind(m_hUdpsock=3) port=7006 <<<

>>> CDUdpStack::bind(m_hUdpsock=4) port=6005 <<<

>>> CDUdpStack::bind(m_hUdpsock=5) port=53 <<<

>>> CDUdpStack::bind(m_hUdpsock=6) port=69 <<<

TA-005 -LE88266-2PH-175CSW-SNMP-122M : IPv6 CLI

Login : # setBlfSubscribeList() !

Run_CodecUi_Fun(): Initialize SIP paremeter !

Run_CodecUi_Fun(): Firware Version= V130422

udp6SelectTos(7, a0)

udpSetSockOpt(m_hUdpsock=7, trafficClass=28)

CDUdpStack::setVlanTag => udpSelectVlan(7, 0)

>>> CDUdpStack::bind(m_hUdpsock=7) port=5060 <<<

udp6SelectTos(8, a0)

udpSetSockOpt(m_hUdpsock=8, trafficClass=28)

CDUdpStack::setVlanTag => udpSelectVlan(8, 0)

>>> CDUdpStack::bind(m_hUdpsock=8) port=5062 <<<

Run_CodecUi_Fun(): iface1,Ip change to 192.168.0.1

Run_CodecUi_Fun(): VoiceMsg_OFF Phone1

Run_CodecUi_Fun(): VoiceMsg_OFF Phone2

Slic6.c port0 Codec event,msg=34!--Run_SLIC_Task

Slic6.c port1 Codec event,msg=34!--Run_SLIC_Task

=== launch_crystal_ND=38 , Id=5! ===

Login : root

Password :

Login Correct

>?

? Show CLI Command

arp ARP Configuration

auth Change User Name and Password

autotest Auto test

autoconfig Auto Confing

autoupdate Auto firmware update

book Edit phone book

cid Select slic Cid

crypto crypto test

debugmode Enter Debug Mode

dhcps Show status of dhcp server

dhcp6s DHCPv6 Server Configuration

dns DNS Configuration

srv Send DNS srv request

ddns DDNS Configuartion

dump Read/Write Memory

exit Exit

fixip Set fixed Ip

ftp Ftp client

http Tx http GET

ipconfig Interface Configuration

mac MAC Configuration

netbuf net buffer info

net NeT Configuration

sock Socket Information

tcp tcp Information

udp udp Information

nat NAT Configuration

virtual_switch Firmware Version

vlan VLAN Configuartion

env6 Set ipv6 enable/disable [0|1]

ndlist Nd Configuration

ndv6 ipv6 ND protocol

ping6 ping6 [-I] [IP-addr|host-name]

mld Multicast Listener Discovery

ping ping [-lN] [IP-addr|host-name]

phone Phone Setting

reboot Reboot

autoreboot Auto Reboot

apsmustencry Auto Config must encryption

reload Reload Factory Setting

route Route Configuration

save Save to flash

sendmsg -[x] [URL] [msg]

sip SIP Configuartion

slic read or write slic registers

sntp SNTP Configuartion

stack Show stack status

staticrt Static Route Configuration

switch switch Configuration

test1 test

test2 test

time Get System Time

update Update Flash Code/RAM

ver Firmware Version

watchdog WatchDog Function

weblogo Change Web's logo

zmalloc zmalloc [size]

zfree memory free test

mausage Memory allocation usage

task Show task status

t38 T38 Configuartion

setccpflag Set PPP CCP on/off flag

setmacrate set mac rate(WAN/LAN)

sendlogto send log to (none/console/syslog)

showctlport show control port

stnmscreg start nmsc reg

stnmscalert send nmsc alert

stopstnmsc stop st_nmsc service

showstnmsc show st_nmsc status

session Session

echotx echotx

echorx echorx

tr069 tr069 command

accountchange tr069 account change command

fshelp Show command of file system

cat Concatenate files/stdin to stdout

echo Show text

ls List file/directory infomation

ll Show file/directory details

rm Remove files/dirctory

mv Rename SOURCE to DEST,or move SOURCE(s) to directory

touch Update/create files

df Show file system information

lzma lzma compress/decompress tool

filedump dump file

autocall Auto call command

OK

>exit

User Abort: Exit

TA-005 -LE88266-2PH-175CSW-SNMP-122M : IPv6 CLI

Login : superuser

Password :

=== launch_crystal_ND=38 , Id=7! ===

*******

Login Correct

>?

? Show CLI Command

arp ARP Configuration

auth Change User Name and Password

autotest Auto test

autoconfig Auto Confing

autoupdate Auto firmware update

book Edit phone book

cid Select slic Cid

crypto crypto test

debugmode Enter Debug Mode

dhcps Show status of dhcp server

dhcp6s DHCPv6 Server Configuration

dns DNS Configuration

srv Send DNS srv request

ddns DDNS Configuartion

dump Read/Write Memory

exit Exit

fixip Set fixed Ip

ftp Ftp client

http Tx http GET

ipconfig Interface Configuration

mac MAC Configuration

netbuf net buffer info

net NeT Configuration

sock Socket Information

tcp tcp Information

udp udp Information

nat NAT Configuration

virtual_switch Firmware Version

vlan VLAN Configuartion

env6 Set ipv6 enable/disable [0|1]

ndlist Nd Configuration

ndv6 ipv6 ND protocol

ping6 ping6 [-I] [IP-addr|host-name]

mld Multicast Listener Discovery

ping ping [-lN] [IP-addr|host-name]

phone Phone Setting

reboot Reboot

autoreboot Auto Reboot

apsmustencry Auto Config must encryption

reload Reload Factory Setting

route Route Configuration

save Save to flash

sendmsg -[x] [URL] [msg]

sip SIP Configuartion

slic read or write slic registers

sntp SNTP Configuartion

stack Show stack status

staticrt Static Route Configuration

switch switch Configuration

test1 test

test2 test

time Get System Time

update Update Flash Code/RAM

ver Firmware Version

watchdog WatchDog Function

weblogo Change Web's logo

zmalloc zmalloc [size]

zfree memory free test

mausage Memory allocation usage

task Show task status

t38 T38 Configuartion

setccpflag Set PPP CCP on/off flag

setmacrate set mac rate(WAN/LAN)

sendlogto send log to (none/console/syslog)

showctlport show control port

stnmscreg start nmsc reg

stnmscalert send nmsc alert

stopstnmsc stop st_nmsc service

showstnmsc show st_nmsc status

session Session

echotx echotx

echorx echorx

tr069 tr069 command

accountchange tr069 account change command

fshelp Show command of file system

cat Concatenate files/stdin to stdout

echo Show text

ls List file/directory infomation

ll Show file/directory details

rm Remove files/dirctory

mv Rename SOURCE to DEST,or move SOURCE(s) to directory

touch Update/create files

df Show file system information

lzma lzma compress/decompress tool

filedump dump file

autocall Auto call command

OK

>

=== launch_crystal_ND=38 , Id=9! ===