Sunny MCU and Electronics

วันอังคารที่ 25 กุมภาพันธ์ พ.ศ. 2557

Linksys WAG160N v1

เราเตอร์ตัวนี้เป็น ADSL2 WiFi Router มีพอร์ต RJ11 1 พอร์ต พอร์ต LAN 4 พอร์ต WiFi แบบ 802.11b/g/n 300 ครับ
ด้านบนของเราเตอร์มีปุ่ม WPS ไฟสถานะ Power, LAN, WiFi, ADSL ,Internet

ด้านหน้า

ด้านหลังมีพอร์ต RJ11, LAN 10/100, ปุ่มรีเซ็ต, และช่องเสียบอแดปเตอร์ 12VDC 1A ครับ

ด้านหลัง

ใต้เครื่องมีสติกเกอร์บอกรายละเอียดเครื่อง การแกะฝาออกต้องขันน็อต 4 ตัวครับ

ใต้เครื่อง

เมื่อแกะฝาออกจะเจอกับบอร์ดวงจร

บอร์ดด้านบน

ตัว CPU กับ Switch มี Heatsink แปะอยู่

CPU กับ Switch

อาศัยข้อมูลจากเว็บ openwrt.com ซึ่งบอกว่า

CPU -> Broadcom BCM6358SKFBG

Switch -> Broadcom BCM5325

Wireless ->

Wireless

ไอซีหลักคือ Atheros AR5416-AC1A

Atheros AR5416-AC1A

RAM -> EtronTech EM6AA160TS-5G เป็น SDRAM ขนาด 32 MB

EtronTech EM6AA160TS-5G

ภาคจ่ายไฟ

ไอซีทั้ง 2 ตัว ในรูปข้างบนคือรุ่นเดียวกันคือ SEMTECH SC4524A 28V 2A Step-Down Switching Regulator

SEMTECH SC4524A

ไอซีภาคจ่ายไฟอีกตัว ทำหน้าที่จ่ายไฟ 5v

ไอซีจ่ายไฟ 5v

ADSL -> Broadcom 6301KSG

Broadcom 6301KSG

อีกด้านของบอร์ด

บอร์ดด้านล่าง

มีไอซี Flash อยู่

Flash -> MX 29LV320CBTC-70G ขนาด 4 MB

MX 29LV320CBTC-70G

ด้านล่างบอร์ดมี Heatsink อยู่กับเสาอากาศแบบภายในเครื่อง 2 ต้นดังรูป

Heatsink ด้านล่างและเสาอากาศภายใน

พอร์ต Serial อยู่ติดมุมด้านหน้า

พอร์ต Serial

Boot log

▒▒▒

CFE version 1.0.37-5.4 for BCM96358 (32bit,SP,BE)

Build Date: 四 1月 10 19:25:21 CST 2008 (root@9DavidZhang2)

Copyright (C) 2000-2005 Broadcom Corporation.

Boot Address 0xbfc00000

Initializing Arena.

Initializing Devices.

Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB

CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz

Total memory: 33554432 bytes (32MB)

Total memory used by CFE: 0x80401000 - 0x80528800 (1210368)

Initialized Data: 0x8041E550 - 0x8041FF60 (6672)

BSS Area: 0x8041FF60 - 0x80426800 (26784)

Local Heap: 0x80426800 - 0x80526800 (1048576)

Stack Area: 0x80526800 - 0x80528800 (8192)

Text (code) segment: 0x80401000 - 0x8041E544 (120132)

Boot area (physical): 0x00529000 - 0x00569000

Relocation Factor: I:00000000 - D:00000000

Board IP address : 192.168.1.1

Host IP address : 192.168.1.100

Gateway IP address :

Run from flash/host (f/h) : f

Default host run file name : vmlinux

Default host flash file name : bcm963xx_fs_kernel

Boot delay (0-9 seconds) : 1

Board Id Name : 96358GW

Psi size in KB : 24

Number of MAC Addresses (1-32) : 10

Base MAC Address : 00:1d:7e:b8:65:8c

Ethernet PHY Type : Internal

Memory size in MB : 32

CMT Thread Number : 0

*** Press any key to stop auto run (1 seconds) ***

Auto run second count down: 0

Code Address: 0x80010000, Entry Address: 0x8022e018

Decompression OK!

Entry at 0x8022e018

Closing network.

Starting program at 0x8022e018

Linux version 2.6.8.1 (root@sbu-ii-1-server) (gcc version 3.4.2) #1 Mon Dec 22

17:27:14 CST 2008

Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB

96358GW prom init

CPU revision is: 0002a010

Determined physical RAM map:

memory: 01fa0000 @ 00000000 (usable)

On node 0 totalpages: 8096

DMA zone: 4096 pages, LIFO batch:1

Normal zone: 4000 pages, LIFO batch:1

HighMem zone: 0 pages, LIFO batch:1

Built 1 zonelists

Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200

brcm mips: enabling icache and dcache...

Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.

Primary data cache 16kB 2-way, linesize 16 bytes.

PID hash table entries: 128 (order 7: 1024 bytes)

Using 150.000 MHz high precision timer.

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 29228k/32384k available (1885k kernel code, 3112k reserved, 278k data, 92k

init, 0k highmem)

Calibrating delay loop... 299.82 BogoMIPS

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Checking for 'wait' instruction... unavailable.

NET: Registered protocol family 16

Total Flash size: 4096K with 71 sectors

File system address: 0xbfc10100

Scratch pad is not used for this flash part.

Can't analyze prologue code at 801e5c1c

Initializing Cryptographic API

PPP generic driver version 2.4.2

NET: Registered protocol family 24

Using noop io scheduler

bcm963xx_mtd driver v1.0

Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank

Amd/Fujitsu Extended Query Table at 0x0040

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

mymtd = 81f82c00

Creating 5 MTD partitions on "Physically mapped flash":

0x00010100-0x00294100 : "fs"

mtd: partition "fs" doesn't start on an erase block boundary -- force read-only

0x00010000-0x003e0000 : "tag+fs+kernel"

0x00000000-0x00010000 : "bootloader"

0x003f0000-0x00400000 : "nvram"

0x003e0000-0x003f0000 : "ath_data"

brcmboard: brcm_board_init entry

Serial: BCM63XX driver $Revision: 1.1.1.1 $

ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX

ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX

blaadd: blaa_detect entry

adsl: adsl_init entry

Broadcom BCMPROCFS v1.0 initialized

u32 classifier

NET: Registered protocol family 2

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

ip_conntrack version 2.1 (253 buckets, 0 max) - 400 bytes per conntrack

ip_ct_h323: init success

ip_conntrack_pptp version 2.1 loaded

ip_conntrack_rtsp v0.01 loading

ip_nat_h323: init success

ip_nat_pptp version 2.0 loaded

ip_nat_rtsp v0.01 loading

ip_tables: (C) 2000-2002 Netfilter core team

netfilter PSD loaded - (c) astaro AG

ipt_random match loaded

NET: Registered protocol family 1

NET: Registered protocol family 17

Ebtables v2.0 registered

NET: Registered protocol family 8

NET: Registered protocol family 20

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (squashfs filesystem) readonly.

Freeing unused kernel memory: 92k freed

init started: BusyBox v1.00 (2008.12.14-06:10+0000) multi-call binary

init started: BusyBox v1.00 (2008.12.14-06:10+0000) multi-call binary

Starting pid 38, console /dev/ttyS0: '/usr/etc/rcS'

Algorithmics/MIPS FPU Emulator v1.5

bcm_enet: module license 'Proprietary' taints kernel.

Broadcom BCM6358A1 Ethernet Network Device v0.3 Dec 22 2008 17:25:47

Config Ethernet Switch Through MDIO Pseudo PHY Interface

dgasp: kerSysRegisterDyingGaspHandler: eth0 registered

eth0: MAC Address: 00:1D:7E:B8:65:8C

losetup: /dev/mtdblock5: No such device or address

mount: Mounting /dev/loop0 on /tmp/fs1 failed: No such file or directory

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=adsl action=start

/bin/cp /proc/uptime /tmp//var/run/rc.adsl.run

/usr/sbin/adslctl start --up

BcmAdsl_Initialize=0x8011A3B8, g_pFnNotifyCallback=0x8021F624

AnnexCParam=0x7FFF7ED8 AnnexAParam=0x00000980 adsl2=0x00000000

pSdramPHY=0xA1FFFFF8, 0x29F31 0xDE25BE6F

AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4

AnnexCParam=0x7FFF7ED8 AnnexAParam=0x00000980 adsl2=0x00000000

dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered

/usr/sbin/adslctl configure --mod a

AnnexCParam=0x7FFF7EC8 AnnexAParam=0x00000980 adsl2=0x00000000

/usr/sbin/atmctl start

ATM proc init !!!

device eth0 entered promiscuous mode

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=printk action=start

/bin/cp /proc/uptime /tmp//var/run/rc.printk.run

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=lan action=start

/bin/cp /proc/uptime /tmp//var/run/rc.lan.run

/sbin/ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255

/usr/bin/killall dhcp-fwd

killall: dhcp-fwd: no process killed

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=wlan action=create

/bin/cp /proc/uptime /tmp//var/run/rc.wlan.run

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=wlan action=start

/bin/cp /proc/uptime /tmp//var/run/rc.wlan.run

start wifi

SIOCSIFHWADDR: No such device

/sbin/wlanconfig: ioctl: No such device

SIOCSIFHWADDR: No such device

SIOCSIFTXQLEN: No such device

SIOCSIFTXQLEN: No such device

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

Error for wireless request "Set Encode" (8B2A) :

SET failed on device ath0 ; No such device.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

Error for wireless request "Set Fragmentation Threshold" (8B24) :

SET failed on device ath0 ; No such device.

Error for wireless request "Set RTS Threshold" (8B22) :

SET failed on device ath0 ; No such device.

/etc/apup: 34: cannot create /proc/sys/net/ath0/debug: Directory nonexistent

Error for wireless request "Set ESSID" (8B1A) :

SET failed on device ath0 ; No such device.

ath0 no private ioctls.

ath0 no private ioctls.

ath0 no private ioctls.

interface ath0 does not exist!

SIOCGIFFLAGS: No such device

wlan up!!

start wifi return 0

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=syslogd action=start

/bin/cp /proc/uptime /tmp//var/run/rc.syslogd.run

/usr/bin/killall -SIGUSR2 syslogd

killall: syslogd: no process killed

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=httpd action=start

/bin/cp /proc/uptime /tmp//var/run/rc.httpd.run

mac = NOT NULL

mac = 001D7EB8658D

mac = NOT NULL

mac = 001D7EB8658D

/bin/rm /tmp/www -f

/bin/ln -sf /www.eng /tmp/www

/usr/sbin/mini_httpd -d /tmp/www -r "Linksys WAG160N " -c '*.cgi' -t 300 -i

/var/run/mini_httpd.pid -S -E /usr/sbin/certSrv.pem &

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=dhcpd action=start

/bin/cp /proc/uptime /tmp//var/run/rc.dhcpd.run

/usr/sbin/udhcpd /etc/udhcpd.conf&

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=ntp action=start

/bin/cp /proc/uptime /tmp//var/run/rc.ntp.run

/usr/sbin/ntp -z GMT+0 2&

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=route action=start

/bin/cp /proc/uptime /tmp//var/run/rc.route.run

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=ripd action=start

/bin/cp /proc/uptime /tmp//var/run/rc.ripd.run

/usr/sbin/iptables -D INPUT -p udp --dport 520 -j ACCEPT

mac = NOT NULL

mac = 001D7EB8658D

Configuration file: /tmp/madwifi.conf

ioctl(SIOCGIFINDEX): No such device

madwifi driver initialization failed.

iptables: Bad rule (does a matching rule exist in that chain?)

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=upnp action=start

/bin/cp /proc/uptime /tmp//var/run/rc.upnp.run

/usr/bin/killall -9 upnpd

killall: upnpd: no process killed

route add -net 239.0.0.0 netmask 255.0.0.0 br0

/usr/sbin/upnpd nas0 br0 30 4&

UPnP Initialized

Intialized UPnP

with fullurl=http://192.168.1.1:49152/gateway.xml

ipaddress=192.168.1.1 port=49152

web_dir_path=/usr/upnp/

desc_doc_url=http://192.168.1.1:49152

Specifying the webserver root directory -- /usr/upnp/

Registering the RootDevice

RootDevice Registered

Initializing State Table

fullurl http://192.168.1.1:49152/gateway.xml

Advertisements Sent

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=wscupnp action=start

/bin/cp /proc/uptime /tmp//var/run/rc.wscupnp.run

/usr/sbin/wscupnpd br0 ath0 30 4&

* *

* * * *

* {~._.~} *

* ( Y ) *

* ()~*~() *

* (_)-(_) *

* *

* *

*

ap_name=yahooODM action=create

/bin/cp /proc/uptime /tmp//var/run/rc.yahooODM.run

Intialized WSC UPnP

The interface br0 exist !

The interface ath0 not exist ! will exit !

Please press Enter to activate this console.

Starting pid 351, console /dev/ttyS0: '/bin/sh'

BusyBox v1.00 (2008.12.14-06:10+0000) Built-in shell (ash)

Enter 'help' for a list of built-in commands.

#

MTD Partition

# cat /proc/mtd

dev: size erasesize name

mtd0: 00284000 00010000 "fs"

mtd1: 003d0000 00010000 "tag+fs+kernel"

mtd2: 00010000 00002000 "bootloader"

mtd3: 00010000 00010000 "nvram"

mtd4: 00010000 00010000 "ath_data"

CPU info

# cat /proc/cpuinfo

system type : 96358GW

processor : 0

cpu model : BCM6358 V1.0

BogoMIPS : 299.82

wait instruction : no

microsecond timers : yes

tlb_entries : 32

extra interrupt vector : no

hardware watchpoint : no

unaligned access : 4

VCED exceptions : not available

VCEI exceptions : not available

ตัวที่ผมนำมารีวิวได้ทดลองใส่เฟิร์มแวร์ OpenWrt ด้วย แต่ลืม Backup Partition ของ ath_data ทำให้ตอนนี้ WiFi ทำงานไม่ได้แล้ว ใครมีสำรองไว้ รบกวนขอหน่วยนะครับ

ผมสำรอง CFE ไว้ด้วย link

Openwrt สำหรับ WAG160N v1 link

เฟิร์มแวร์เดิมของเครื่อง link

วันพุธที่ 19 กุมภาพันธ์ พ.ศ. 2557

Airlive AP60-EU

ตัวนี้มี 4 พอร์ต LAN ส่วนพอร์ต WAN ใช้รุ่วมกับ LAN ช่อง 1 ครับ กำลังส่งตัวนี้ 800 mW ไวเลส N150

ด้านหน้าเครื่อง

ด้านหน้าตัวเครื่องมีไฟสถานะ Power, WPS, LAN1-4

ด้านหลังเครื่อง

ด้านหลังมีพอร์ต LAN 4 พอร์ต ปุ่ม Reset, WPS, ช่องเสียบเสาอากาศ และช่องเสียบอแดปเตอร์ 12VDC 1A

ใต้เครื่อง

ใต้เครื่องมีรูน็อต 4 รู และสติกเกอร์

สติกเกอร์

สติกเกอร์บอกรายละเอียดต่างๆ ของเราเตอร์

บอร์ดด้านบน

ตัวบอร์ดมีไอซีต่างๆดังนี้

CPU -> Realtek RTL8196C

Realtek RTL8196C

Flash -> MXIC 25L3206E ขนาด 4 MB

MXIC 25L3206E

RAM -> Windbond W9825G6JH-6 ขนาด 32MB

Windbond W9825G6JH-6

Wireless -> Realtek RTL8188RE IEEE 802.11b/g/n 1T1R

Realtek RTL8188RE

Regulator -> LSC LSP5503 3A Synchronous Step Down DC/DC Converter

LSC LSP5503

ด้านหลังบอร์ดไม่มีไอซีอยู่

บอร์ดด้านใต้

พอร์ตภายใน

JTAG ->

JTAG

Serial ->

Serial

Boot log

SPI

SDRAM CLOCK:156MHZ

chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize

0h c22016h c2h 20h 16h 0h 16h 400000h

blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName

10000h 40h 1000h 400h 100h 10h 4eh MX25L3205D

RealTek(RTL8196C)at 2011.10.15-00:32+0800 version v1.1g Emergency [16bit](390MHz)

no sys signature at 00010000!

no sys signature at 00020000!

no sys signature at 00030000!

no rootfs signature at 000E0000!

no rootfs signature at 000F0000!

no rootfs signature at 00130000!

Jump to image start=0x80500000...

decompressing kernel:

Uncompressing Linux... done, booting the kernel.

done decompressing kernel.

start address: 0x800034c0

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 27408k/32768k available (2290k kernel code, 5360k reserved, 422k data, 104k

init, 0k highmem)

Calibrating delay loop... 389.12 BogoMIPS (lpj=1945600)

Mount-cache hash table entries: 512

net_namespace: 524 bytes

NET: Registered protocol family 16

bio: create slab <bio-0> at 0

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

NET: Registered protocol family 1

squashfs: version 4.0 (2009/01/31) Phillip Lougher

io scheduler noop registered

io scheduler cfq registered (default)

Realtek GPIO Driver for Flash Reload Default

Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled

serial8250: ttyS0 at MMIO 0x18002000 (irq = 8) is a 16550A

PPP generic driver version 2.4.2

MPPE/MPPC encryption/compression module registered

NET: Registered protocol family 24

RTL8192C/RTL8188C driver version 1.6 (2011-07-18)

=====>>INSIDE rtl8192cd_init_one <<=====

96C - 40MHz Clock Source

vendor_deivce_id=819110ec

=====>>EXIT rtl8192cd_init_one <<=====

=====>>INSIDE rtl8192cd_init_one <<=====

=====>>EXIT rtl8192cd_init_one <<=====

=====>>INSIDE rtl8192cd_init_one <<=====

=====>>EXIT rtl8192cd_init_one <<=====

=====>>INSIDE rtl8192cd_init_one <<=====

=====>>EXIT rtl8192cd_init_one <<=====

=====>>INSIDE rtl8192cd_init_one <<=====

=====>>EXIT rtl8192cd_init_one <<=====

=====>>INSIDE rtl8192cd_init_one <<=====

=====>>EXIT rtl8192cd_init_one <<=====

Probing RTL8186 10/100 NIC-kenel stack size order[2]...

chip name: 8196B, chip revid: 0

Set 8196C PHY Patch OK

NOT YET

Set threshould idx 0

Set threshould idx 1

eth0 added. vid=9 Member port 0x1...

eth1 added. vid=8 Member port 0x10...

eth2 added. vid=9 Member port 0x2...

eth3 added. vid=9 Member port 0x4...

eth4 added. vid=9 Member port 0x8...

[peth0] added, mapping to [eth1]...

SPI INIT

SDRAM CLOCK:156MHZ

SPI flash(MX25L3205D) was found at CS0, size 0x400000

Creating 2 MTD partitions on "flash_bank_1":

0x000000000000-0x000000200000 : "boot+cfg+linux"

0x000000200000-0x000000400000 : "root fs"

nf_conntrack version 0.5.0 (512 buckets, 2048 max)

ip_tables: (C) 2000-2006 Netfilter Core Team

TCP cubic registered

NET: Registered protocol family 17

VFS: Mounted root (squashfs filesystem) readonly on device 31:1.

Freeing unused kernel memory: 104k freed

init started: BusyBox v1.13.4 (2013-01-17 11:25:18 CST)

set wireless ack timeout....

Init Start...

Init bridge interface...

device eth0 entered promiscuous mode

device eth1 entered promiscuous mode

device wlan0 entered promiscuous mode

[PHY_ConfigMACWithParaFile][MACPHY_REG_92C]

===> Load_92C_Firmware

<=== Load_92C_Firmware

br0: port 3(wlan0) entering forwarding state

br0: port 2(eth1) entering forwarding state

br0: port 1(eth0) entering forwarding state

Invalid DNS server setting

Init Wlan application...

iwcontrol RegisterPID to (wlan0)

route: SIOCDELRT: No such process

IEEE 802.11f (IAPP) using interface br0 (v1.7)

br0: port 2(eth1) entering disabled state

br0: port 2(eth1) entering forwarding state

IPD Start !!

#

#

MTD partition

# cat /proc/mtd

dev: size erasesize name

mtd0: 00200000 00001000 "boot+cfg+linux"

mtd1: 00200000 00001000 "root fs"

ผมสำรองไฟล์ของ mtd ไว้ด้วยครับ

mtd0

mtd1

Belkin F7D1301 v1

เราเตอร์ตัวนี้ใช้เสาภายในตัวเครื่อง มี LAN 4, WAN 1 ,Wireless เป็นแบบ 802.11b/g/n

ด้านหน้าเครื่อง

ด้านหน้าเครื่องมี LED 1 ดวงกับปุ่ม WPS

ด้านหลังเครื่อง

ด้านหลังมี LAN 4 พอร์ค WAN 1 พอร์ต ปุ่ม Reset และช่องเสียบอแดปเตอร์จ่ายไฟขนาด 9VDC 1A ผมใช้ 12 DC 1A ก็สามารถใช้ได้ปกติ

ฐานเครื่อง

ที่ฐานเครื่องมีสติกเกอร์บอกรายละเอียดเครื่อง การแกะเครื่องต้องขันน็อต 2 ตัวที่อยู่ใต้สติกเกอร์น้ก่อน

บอร์ดด้านบน

ตัวบอกร์ดด้านบน มีไอซีและอุปกรณ์สำคัญๆ คือ

CPU -> Broadcom BM5356A1KFBG

Broadcom BCM5356A1KFBG

RAM -> Winbond W9864G6IH-6 ขนาด 8 MB

Winbond W9864G6IH-6

Flash -> MXIC 25L1605DM2I ขนาด 2 MB

MXIC 25L1605DM2I

เสาอากาศ

เสาอากาศภายในตัวเครื่อง

พลิกอีกด้านเป็นบอร์ดโล่งๆ

บอร์ดด้านล่าง

หน้าเว็บตั้งค่าของเราเตอร์

หน้าตั้งค่า

การเชื่อมต่อ Serial เพื่อดู Boot log ต่อตามรูป โดยตั้งความเร็วที่ 115200

ขา Serial

Boot Log

Decompressing...done

Decompressing...done

Init Arena

Init Devs.

Boot partition size = 131072(0x20000)

Found a 2MB ST compatible serial flash

et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.36

CPU type 0x19749: 333MHz

Tot mem: 8192 KBytes

CFE mem: 0x80700000 - 0x807DD1B0 (905648)

Data: 0x80732F50 - 0x807361B0 (12896)

BSS: 0x807361B0 - 0x807771B0 (266240)

Heap: 0x807771B0 - 0x807DB1B0 (409600)

Stack: 0x807DB1B0 - 0x807DD1B0 (8192)

Text: 0x80700000 - 0x80732F48 (208712)

Copying boot params.....DONE

Arcadyan bootloader version 1.19 boot_version 1.19

Press space bar to cancel startup...

Device eth0: hwaddr 94-44-52-63-CC-DD, ipaddr 192.168.2.1, mask 255.255.255.0

gateway not set, nameserver not set

Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)

Loading: [ZIP 3] [ZIP 1] done 0 bytes read

Entry at 0x80002000

Closing network.

In c_entry() function ...

[Init_TFTP_buffer_behind_end] TFTP_buffer = 806e18e0

[Init_TFTP_buffer_behind_end] TFTP_BUFSIZE = 1181472

CPU ProcId is: 0x00019749, options: 0x000021cd

CPU: BCM5356 rev 1 at 333 MHz

install_exception

Set C0 SR to 0x10000000

Co config = 80240483

sys_irq_init ...

Before entering coretest_main

##### _ftext = 0x80002000

##### _fdata = 0x80225850

##### __bss_start = 0x8027661C

##### end = 0x806C1750

##### Backup Data from 0x806E18E0 to 0xBFDA0000~0xBFDF0DCC len 331212

Found a 2MB ST compatible serial flash

[initialize_data_area] DATA area was already backuped in flash ..

[INIT] System Log Pool startup ...

[INIT] MTinitialize ..

[INIT] usrclk

CPU Clock 300000000 Hz

mips_counter_frequency:150000000

r4k_offset: 0x000249f0(150000)

init_US_counter : time1 = 268790 , time2 = 32268847, diff 32000057

US_counter = 64

cnt1 33228151 cnt2 33229829, diff 1678

r4k_cur:0x0206a70e(-2140367196)

End of usrclk_init

mips_int_enable: 5

mips_int_enable 1: s = 8000

mips_int_enable 2: s = 8000

mips_int_enable 3: s = 0

Runtime code version: 1.00.22

System startup...

[INIT] Memory COLOR 0, 810000 bytes ..

[INIT] Memory COLOR 1, 400000 bytes ..

[INIT] Memory COLOR 2, 401200 bytes ..

PCI: no core

[pci_alloc_bus] alloc memory 8042797c

[pci_do_scan_bus]Scanning bus 00

Found bus:devfn[vid/did]class header_type 00:00 [14e4/0800] 000501 00

[pci_fixup_device]: vendor= 0x14e4 dev=0x800 devfn= 0x0

PCI: Calling quirk 800DCCF8 for 00:00.0

Found bus:devfn[vid/did]class header_type 00:08 [14e4/4338] 000280 00

[pci_fixup_device]: vendor= 0x14e4 dev=0x4338 devfn= 0x8

PCI: Calling quirk 800DCCF8 for 00:01.0

Found bus:devfn[vid/did]class header_type 00:10 [14e4/4715] 000200 00

[pci_fixup_device]: vendor= 0x14e4 dev=0x4715 devfn= 0x10

PCI: Calling quirk 800DCCF8 for 00:02.0

Found bus:devfn[vid/did]class header_type 00:20 [14e4/0835] 00ffff 00

[pci_fixup_device]: vendor= 0x14e4 dev=0x835 devfn= 0x20

PCI: Calling quirk 800DCCF8 for 00:04.0

Fixups for bus 00

PCI: Fixing up bus 0

Bus scan for 00 returning with max=00

[pci_fixup_device]: vendor= 0x14e4 dev=0x800 devfn= 0x0

[pci_fixup_device]: vendor= 0x14e4 dev=0x4338 devfn= 0x8

[pci_fixup_device]: vendor= 0x14e4 dev=0x4715 devfn= 0x10

[pci_fixup_device]: vendor= 0x14e4 dev=0x835 devfn= 0x20

RUNTASK id=1 iNetTask ...

[generic_flash_id_ok] flash already initialized ..

SFLASH Init OK!

FLASH boot parameter signature found!!16B9fa44fe64

Boot Parameters found !!!

Bootcode version: 1.19

Serial number: 121016G1119767

Hardware version: 01

sizeof(struct III_Config_t) is 70828, nLen:70828, Magic:0x33343536

my CFGVersionMagic = 33343536, old CFGVersionMagic on flash = 33343536

my CFGsize = 70848, my CFGDescSize = 17755

my Version = 1.00.22, Version on flash= 1.00.16

[CONFIG] flash version:[1.00.16], [-2146958928.-2146959484.2-45]

CFGsize on flash = 70848, CFGDescSize on flash = 17778

OldCfgHexSize:6077

Unzipping from 8040C200 to 80407C7C ... [ZIP 1] done

Uncompressed size = 17776

Tail1 : END_III_Config_t

Size of Old CFG_DESC is :17776!!!

useCfgDesc:1

MyCfgHexSize:6063

Unzipping from 8040C200 to 80403710 ... [ZIP 1] done

Uncompressed size = 17753

My CFGDescSize:17755

useCfgDesc:1

Tail : END_III_Config_t

useCfgDesc:3

Restore Config file from ver:1.00.16!!!

[CONFIG] Configuration in Flash is old version: -2146958928.-2146959484.45

[CONFIG] DS_Tail:[t_F7D1301 v1]

default route: 0.0.0.0

BufferInit:

BUF_HDR_SZ=160 BUF_ALIGN_SZ=20 BUFFER_OFFSET=384

BUF_BUFSZ0=608 BUF_BUFSZ1=2272

NUM_OF_B0=0 NUM_OF_B1=500

BUF_POOL0_SZ=0 BUF_POOL1_SZ=1216000

sizeof(BUFFER0)=768,sizeof(BUFFER1)=2432

*BUF0=0x805c9cfc *BUF1=0x804a0edc

Altgn *BUF0=0x805c9d00 *BUF1=0x804a0ee0

End at BUF0:0x805c9d00, BUF1:0x805c9ce0

buffer0 pointer init OK!

buffer1 pointer init OK!

ifno= 0, Link_Type= 4

Interface 0 ip = 127.0.0.1

ifno= 1, Link_Type= 1

[pci_set_master]

PCI: Enabling bus mastering for device 00:02.0

PCI: Setting latency timer of device 00:02.0 to 64

[pci_enable_device]

[pci_set_power_state] dev->device=0x4715 state=0

[dma64_alloc] alloc 128 dma tx descriptor size=10240(0x2800)

[dma64_alloc] alloc 256 dma rx descriptor size=12288(0x3000)

[dma64_alloc] alloc 128 dma tx descriptor size=6144(0x1800)

[dma64_alloc] alloc 128 dma tx descriptor size=6144(0x1800)

[dma64_alloc] alloc 128 dma tx descriptor size=6144(0x1800)

mips_int_enable: 2

mips_int_enable 1: s = 8000

mips_int_enable 2: s = 9000

mips_int_enable 3: s = 0

: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.68

MAC Address: 94:44:52:63:cc:dd

Interface 1 ip = 192.168.2.1

ifno= 2, Link_Type= 1

init_hwlan_multicast_slot()...

hwlan_init(241): [HWLAN] ifno=2 irno=7 port=0x00000000

[hwlan_init] if_table[2]::94-c0-a8-02-01-02

[hwlan_init] if_table[2]::94-44-a8-02-01-02

[hwlan_init] if_table[2]::94-44-52-02-01-02

[hwlan_init] if_table[2]::94-44-52-63-01-02

[hwlan_init] if_table[2]::94-44-52-63-cc-02

[hwlan_init] if_table[2]::94-44-52-63-cc-dd

[pci_enable_device]

[pci_set_power_state] dev->device=0x4338 state=0

[pci_set_master]

PCI: Enabling bus mastering for device 00:01.0

PCI: Setting latency timer of device 00:01.0 to 64

RUNTASK id=2 rapi_tmr_task ...

TR switch isolation:6c

origional pa0maxpwr=4a

Power Offset: pi->txpa_2g[0]:0x16b9

Power Offset: pi->txpa_2g[1]:0xfffffa44

Power Offset: pi->txpa_2g[2]:0xfffffe64

[dma64_alloc] alloc 256 dma tx descriptor size=12288(0x3000)

[dma64_alloc] alloc 256 dma rx descriptor size=12288(0x3000)

[dma64_alloc] alloc 256 dma tx descriptor size=12288(0x3000)

[dma64_alloc] alloc 256 dma tx descriptor size=12288(0x3000)

[dma64_alloc] alloc 256 dma tx descriptor size=12288(0x3000)

[dma64_alloc] alloc 256 dma tx descriptor size=12288(0x3000)

[dma64_alloc] alloc 256 dma tx descriptor size=12288(0x3000)

mips_int_enable: 1

mips_int_enable 1: s = 9000

mips_int_enable 2: s = 9800

mips_int_enable 3: s = 0

: Broadcom BCM4338 802.11 Wireless Controller 5.10.56.68

Interface 2 ip = 192.168.2.1

ifno= 3, Link_Type= 1

MAC Address: 94:44:52:63:cc:de

iput_IpLinkUp(ifno=3)> ifp->add_default_route:1

Re-Init NAT data structure

Init NAT data structure

Interface 3 ip = 0.0.0.0

ifno= 4, Link_Type= 0

ifno= 5, Link_Type= 0

ifno= 6, Link_Type= 0

ifno= 7, Link_Type= 0

ifno= 8, Link_Type= 0

ifno= 9, Link_Type= 0

ifno= 10, Link_Type= 0

ifno= 11, Link_Type= 0

ifno= 12, Link_Type= 0

ifno= 13, Link_Type= 0

ifno= 14, Link_Type= 0

ifno= 15, Link_Type= 0

ifno= 16, Link_Type= 0

Init NAT data structure

No default route, no need to reinit the NAT data structure

RUNTASK id=5 if_task if0...

RUNTASK id=6 if_task if1...

RUNTASK id=7 if_task if2...

RUNTASK id=8 if_task if3...

RUNTASK id=9 timer_task...

RUNTASK id=10 conn_mgr...

RUNTASK id=11 main_8021x...

RUNTASK id=12 main_lltd...

RUNTASK id=13 period_task...

RUNTASK id=14 dhcp_daemon...

RUNTASK id=15 dhcp_clt...on interface 3

[flash_init] PFS web (bfcf6000) in flash ...

[flash_init] set drive_start_addr[0] as bfcf6000

httpd: listen at 192.168.2.1:80

RUNTASK httpd...

RUNTASK id=18 dnsproxy...

RUNTASK id=19 dhcpd_mgmt_task...

UPnP is enabled

UPNP Device initialize success! slot=20

>>> belkin_wan_cfg task runs successfully, task_id = 21

gConfig.WSC_Mode:2

RUNTASK id=22 wscmain...

RUNTASK id=23 wsc_Send_eap_packet...

RUNTASK id=24 wsc_Send_UPNP_packet...

RUNTASK id=25 WSC_WaitUserAction_Task...

gConfig.WSC_Mode:2

Starting Multitask...

gSetting.lang_id = 0

run_project_task

RUNTASK id=26 apAppInit...

ifno2dot1x_if[2]=0

dot1x_wireless_if_mask=0x4

[reset_802dot1x] wireless module ready

[wl_open] done

[init_wpa] dot1x_ready[0]=1

[reset_802dot1x] 802.1Xv2 ready

*********************************************

Wi-Fi Simple Config Application - Intel Corp.

Version: Build 1.02, Aug 31 2010 14:35:24

*********************************************

Initializing stack...

---------in wsc init----------

----------sizeof(uint32)=4

----------sizeof(uint-long)=4

----------sizeof(uint32)=2

[22]pthread_cond_init: 0

[22]pthread_mutex_init: resource No. 33

[22]pthread_mutex_init: resource No. 34

[PORTABLITY]:WscCreateThread--------------------

@#*@#*@#*EAP-WSC: Entered eap_wsc_init *#@*#@*#@

Entered udp_read

wsc_Send_eap_packet:udpFdupnp_wcn:15;;udpFdupnp:17

WscCmd:ActualCBThreadProc: Started

GenaInit : event_hook is NULL!!

[22]pthread_cond_init: 1

[22]pthread_mutex_init: resource No. 35

[22]pthread_mutex_init: resource No. 36

[PORTABLITY]:WscCreateThread--------------------

WscCmd:ActualUIThreadProc: Started.

ActualUIThreadProc: wait q

MasterControl constructor

WscCmd::MC instantiated ok

[22]pthread_cond_init: 2

[22]pthread_mutex_init: resource No. 37

[22]pthread_mutex_init: resource No. 38

[PORTABLITY]:WscCreateThread--------------------

[22]pthread_mutex_init: resource No. 39

[PORTABLITY]:pthread_mutex_init--------------------

CTransport Construction

[22]pthread_cond_init: 3

[22]pthread_mutex_init: resource No. 40

[22]pthread_mutex_init: resource No. 41

[PORTABLITY]:WscCreateThread--------------------

In CTransport::ActualCBThreadProc

ActualCBThreadProc: Calling Dequeue

[HWLAN] Ready

MC::Init: Init complete ok

WscCmd::MC intialized ok

WscCmd::Init ok, starting stack...

Info::ReadConfigFile: Called

Info::ReadConfigFile: "▒

Info::ReadConfigFile:File open ok

******************uuid_p:0x0000000000000001100094445263ccdd*****

mp_deviceInfo->uuid[i]:

0-0-0-0-0-0-0-1-10-0-94-44-52-63-cc-dd-

mp_deviceInfo->macAddr:94:44:52:63:CC:DD

gSetting.dot1x.if_entry[0].enableWEP:0

authTypeFlags is 1 ,encrTypeFlags is 1 ,m_nwKey is , key len is 0

ssid is Belkin.3CDD54

S, bf9

E, e25

MC::SwitchModeOn: EModeApProxyRegistrar enter

RegistrarSM constructor

[22]pthread_cond_init: 4

[22]pthread_mutex_init: resource No. 42

[22]pthread_mutex_init: resource No. 43

[PORTABLITY]:WscCreateThread--------------------

RegistrarSM constructor

[22]pthread_cond_init: 5

[22]pthread_mutex_init: resource No. 44

[22]pthread_mutex_init: resource No. 45

[PORTABLITY]:WscCreateThread--------------------

[22]pthread_mutex_init: resource No. 46

[PORTABLITY]:pthread_mutex_init--------------------

MC::SetBeaconIE: call to trans->SetBeaconIE() ok

MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok

mp_deviceInfo->authTypeFlags:1

mp_deviceInfo->encrTypeFlags:1

cp_data[13]:Belkin.3CDD54

mp_deviceInfo->authTypeFlags:1

mp_deviceInfo->encrTypeFlags:1

*******build M1 start**********

RPROTO: BuildMessageM1_For_REG built: -2143386944 bytes

*******build M1 end**********

after InitializeSM....

in startMonitor....

CInbEap Construction

Sizeof(WSC_NOTIFY_DATA) = -2143386848

---test--sizeof(WSC_NOTIFY_DATA) = 36

[22]pthread_cond_init: 6

[PORTABLITY]:WscCreateEvent--------------------

Entered udp_open

Socket open successful, sd: -2143386864

Entered udp_open

Socket open successful, sd: -2143386864

Entered udp_bind

Binding successful for socket [-2143386880]

[PORTABLITY]:WscCreateThread--------------------

In CInbEap::StaticRecvThread

CInbEap::ActualRecvThread Started

Entered udp_read

exit StartMonitor TRANSPORT_TYPE_UPNP_DEV

in startMonitor....

CInbUPnPDev Construction

Entered udp_open

Socket open successful, sd: -2143386864

Entered udp_open

Socket open successful, sd: -2143386864

Entered udp_bind

Binding successful for socket [-2143386880]

CInbUPnPDev StartMonitor

[PORTABLITY]:WscCreateThread--------------------

exit switch_mode

MC::SwitchModeOn: Exit

MC::StartStack: Informing app of mode

In CInbUPnPDev::StaticUPnPThread

end UPnPCreateMicroStack

Entered udp_read

-WscCmd::CallbackProc Enqueue done

MC::SwitchModeOn: Done callback

exit wscmain

@@[27]pthread_mutex_unlock: the res is free 33-- -2145275408

WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd

******* MODE: AP with built-in Registrar and UPnP Proxy *******

-@@[20]pthread_mutex_unlock: the res is free 35-- -2145273768

*******p_header->eType:5

StartCheckInternetStatus =1

LCB_MENU_AP_PROXY_REGISTRAR

**************b_tryAgain:1

Options:

0. Quit

1. Configure Client

2. Configure Client via push-button

Enter selection: [htf_dbg] - OnlineActiveWirless() 2018

###BCM5356 region was set when setting country code###

cck:chan=4,origional power=48

ofdm: chan=4,origional power=48

Setting Wireless Country Code : 0x33a

Setting DTIMPeriod : 1

Setting BeaconPeriod : 100

Setting gfragThreshold:2346

Setting grtsThreshold:2347

Setting PreambleType:0

Setting TxBurst:1

Setting TxAntenna:3

wme_ac ap bk ecwmax 6 ecwmin 3 txop 0 aifsn 3 acm 0

wme_ac ap be ecwmax 10 ecwmin 3 txop 0 aifsn 7 acm 0wme_ac ap vi ecwmax 5 ecwmin 3

txop 94 aifsn 1 acm 0wme_ac ap vo ecwmax 3 ecwmin 2 txop 47 aifsn 1 acm 0wme_ac sta

bk ecwmax 10 ecwmin 4 txop 0 aifsn 3 acm 0wme_ac sta be ecwmax 10 ecwmin 4 txop 0

aifsn 7 acm 0wme_ac sta vi ecwmax 4 ecwmin 3 txop 94 aifsn 2 acm 0wme_acSetting

APSDCapable:0

Setting GF_Mode:0

Setting ShortGI 20MHz:1 40MHz:1

Setting Mpdudensity:6

Setting AMSDU enable:0

Setting interfernce 4

cck:chan=4,origional power=48

ofdm: chan=4,origional power=48

Netgear WGR614 v5

เราเตอร์ตัวนี้มี 4 พอร์ต LAN และ 1 พอร์ต WAN ครับ เสาไวไฟถอดเปลี่ยนไม่ได้ มีโหมด 802.11b, 802.11g

ด้านหน้า

ด้านหน้ามีไฟสถานะ Power, Test, Wireless, Internet, LAN1-4

ด้านหลัง

ด้านหลังมีพอร์ต WAN, LAN และช่องเสียบอแดปเตอร์ 12vdc 1a

ใต้เครื่อง

ใต้เครื่องมีสติกเกอร์ น็อตมี 4 ตัวใต้ยางรอง

สติกเกอร์

สติกเกอร์บอกหน้าที่ของไฟต่างๆ และอธิบายพอร์ตแต่ละพอร์ต

บอร์ดด้านบน

ตัวบอร์ดด้านบนมีไอซีสำคัญๆ คือ

CPU -> Broadcom BCM5350KPB5

Broadcom BCM5350KPB5

Flash -> MX 29LV800BTTC-90 ขนาด 1 MB

MX 29LV800BTTC-90

RAM -> Samsung K4S641632H-TC75 ขนาด 8 MB

Samsung K4S641632H-TC75

Wireless -> Broadcom BCM2050KML 802.11a/b/g

โมดูล Wireless ที่อยู่ในบอดีโลหะ

Broadcom BCM2050KML

Inverter -> NXP 74LVC04AD

NXP 74LVC04AD

ภาคจ่ายไฟ

บนบอร์ดมีการทำเผื่อ USB 2 ช่อง

ช่อง USB 2 ช่อง

ด้านล่างของบอร์ดไม่มีไอซีใดๆ

ด้านล่างของบอร์ด

การต่อ Serial เข้ากับคอมพิวเตอร์ทำได้ตามภาพ โดยตั้งความเร็วที่ 115200

Serial

Boot log

CFE ver 1.0.2(Top) Mon Sep 27 09:03:01 CST 2004

et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 2004.4.28.0

Decompressing... \muxDevLoad failed for device entry 1!

muxDevLoad failed for device entry 2!

muxDevLoad failed for device entry 4!

Failed to attach to device Attaching interface lo0...done

BCM47xx VxWorks BSP - Oct 25 2005 14:45:02

Flash : MX29LV800B 1Mx8 TopB

pinglib init

configure vlans

configure vlans...done

0x807ffdf0 (): task deadCan't attach unknown device (unit 0).

CC module initialized successfully

WAN Initialisation [SUCCESS]

PPTP Initialised

Firewall INIT completed

AD Init completed FW initalized

IGWIpRsmInit(): ....End

vxBitsInit

add interface mirror0

DNS redirect INIT

in abRegisterInputHook inputPktHook: 802193c0

BlockSides keywords WebAppControl add successfully

Syslog configuration successfully updated

Info: No FWPT default policies.

DHCPS: init dhcps: devname=mirror0

DHCPS:Set the default Lease Time to 86400

Set option ACOS_DHCP_OPT_ROUTER to 192.168.1.1:

Set option ACOS_DHCP_OPT_DNS_SERVER to 192.168.1.1:

NAS task tNASlan started.

Login: No interface specified. Quitting...

===== DHCP LEASE_NEW =====

dns_server 1 = 192.168.10.1

wan gateway = 192.168.10.1

wan hostname = WGR614v5

add interface mirror0

add interface et0

add interface mirror0

add interface et0